18 open source boards using the SFH617A-1
Real designs built with the SFH617A-1, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Pcbtc
lucysrausch
100 × 100 mm96 parts2LNo license223AcCCS
IdahoLabResearch
172.1 × 143.5 mm106 parts2LMIT18AVR/Arduino
Rpi dbt03
bildschirmtext
64 × 56 mm36 parts2LMIT11AVR/Arduino
Nova 1200 front panel
ForgottenMachines
397.5 × 119.4 mm203 parts2LNo license5AVR/Arduino
Arduino relay
bhaskar9980
128 × 47.4 mm58 parts2LMIT5Fault Latch 2
JacobParent7
110 × 90 mm101 parts2LNo license4Tesla-Coil-MIDI-Synth
ucsbieee
132.1 × 61 mm94 parts4LNo license4ESP32
Telepresence bot
yash101
116 × 100 mm183 parts4LNo license0STM32
BobinaTeslaMusical
MarcoBravoG
100 × 100 mm96 parts2LGPL-3.00Jacart electronics
JACart
152.4 × 147.3 mm44 parts2LNo license0Hardware-Electronics
JACart2
152.4 × 147.3 mm44 parts2LNo license0Charging
JacobParent7
80 × 70 mm49 parts2LNo license4BPSD-2025
LSUTigerRacing
68.5 × 43 mm50 parts2LNo license7RP2040/RP2350
PSU
MUNAKATA-EPC
38 × 37.2 mm46 parts2LNo license0Charging
LSUTigerRacing
80 × 70 mm49 parts2LNo license7RML
JacobParent7
85 × 50 mm25 parts4LNo license4Kicker
MUNAKATA-EPC
38 × 37.2 mm22 parts2LNo license0RML
LSUTigerRacing
85 × 50 mm25 parts4LNo license7
How designs wire the SFH617A-1
Read from the KiCad layouts of 13 open source designs, one per repository: what each pin of the SFH617A-1 connects to, and the resistors, capacitors and other passives placed on it.
- Pin 1 has a series resistor on 7 of 13 designs, most often 120 Ω (then 1 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: A connector 23% |
|
| Pin 3 | Connected to: Signal 69% · GND 31% |
|
| Pin 4 | Connected to: Signal 54% · 5V 46% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Pcbtc by lucysrausch, AcCCS by IdahoLabResearch, Rpi dbt03 by bildschirmtext and BPSD-2025 by LSUTigerRacing.
The SFH617A-1 in open source designs
The gallery holds 18 open source boards using the SFH617A-1 from 13 GitHub repositories; a typical one measures about 100 × 70 mm and carries around 50 components.
78% are two-layer designs, the rest use four layers or more, and 22% carry an open source license.
The most starred is Pcbtc by lucysrausch.
Parts used alongside the SFH617A-1
Microcontrollers on boards using the SFH617A-1
What boards using the SFH617A-1 are built for
SFH617A-1: common questions
Where can I find a SFH617A-1 reference design?
Each of the 18 boards on this page is a real design using the SFH617A-1. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the SFH617A-1 pin 1?
Pin 1 has a series resistor on 7 of 13 designs, most often 120 Ω (then 1 kΩ). Counted from the KiCad layouts of 13 open source designs using the SFH617A-1.
What parts are used alongside the SFH617A-1?
The 641964-1, 74AHC1G00, 74LS279, 74LVC1G11 and 74LVC2G86 appear in the most repositories here.
Which microcontrollers do boards using the SFH617A-1 use?
Most are built on AVR/Arduino (3), STM32 (2), ESP32 (1) and RP2040/RP2350 (1).
How big is a typical board using the SFH617A-1?
The median is 100 × 70 mm, and 78% are two-layer designs.
What is the most popular open source board using the SFH617A-1?
By GitHub stars, Pcbtc by lucysrausch, with 223 stars.
Can I simulate one of these boards using the SFH617A-1 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.