12 open source boards using the TCA9548A
Real designs built with the TCA9548A, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Stm32pe midi
udu3324
307 × 46.1 mm135 parts4LGPL-3.035Triaxial loadcell breakout
Scottapotamas
60 × 30 mm52 parts2LNo license4AVR/Arduino
Luci sdk encoders
lucimobility
68.6 × 53.3 mm25 parts2LApache-2.01RP2040/RP2350
Sentinel HYDRA
SridharCodeVersion
93.5 × 91 mm135 parts6LApache-2.00RP2040/RP2350
Sentinel HYDRA
SridharCodeVersion
93.5 × 91 mm135 parts6LApache-2.00RP2040/RP2350
HardwareInterfaceBoard
plb500
146.2 × 91.2 mm81 parts2LNo license0RP2040/RP2350
M5Stamp-Pico VL53L4CX KP-BNO055
see-ranked
80 × 80 mm20 parts2LNo license0ESP32
CARVanta Sentinel v2
SridharCodeVersion
100 × 100 mm86 parts6LApache-2.00ESP32
CARVanta Sentinel v2
SridharCodeVersion
100 × 100 mm86 parts6LApache-2.00- schematic only · 131 partsRaspberry Pi
Wanos board
gitwannes
131 parts2LCustom license1 RadioSupport
LadyRoninEngineer
44 × 50 mm21 parts2LUnlicense34Raspberry Pi
CPU
jonathan-tooley
265.4 × 95.3 mm32 parts2LNo license0
How designs wire the TCA9548A
Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the TCA9548A connects to, and the resistors, capacitors and other passives placed on it.
- The SCL pin has a pull-up to 3.3V on 3 of 7 designs, most often 4.7 kΩ (then 2.2 kΩ).
- The SDA pin has a pull-up to 3.3V on 3 of 7 designs, most often 4.7 kΩ (then 2.2 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| SCL/SPC_1pin 1 | Connected to: ADS1256IDBR 22%, LMP91000 22% · 5V 44% |
|
| GNDpin 2 | Connected to: ADS1256IDBR 22%, LMP91000 22% · GND 44% |
|
| INT2_5pin 5 | Connected to: A connector 22% · not connected 33% |
|
| A0pin 6, 22 | Connected to: A connector 31% · not connected 31% |
|
| SCLpin 19 | Connected to: A connector 43% |
|
| SDApin 20 | Connected to: A connector 43% |
|
15 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Stm32pe midi by udu3324, RadioSupport by LadyRoninEngineer, Triaxial loadcell breakout by Scottapotamas and Luci sdk encoders by lucimobility.
The TCA9548A in open source designs
The gallery holds 12 open source boards using the TCA9548A from 10 GitHub repositories; a typical one measures about 93.5 × 91 mm and carries around 84 components.
58% are two-layer designs, the rest use four layers or more, and 58% carry an open source license.
The most starred is Stm32pe midi by udu3324.
Parts used alongside the TCA9548A
Microcontrollers on boards using the TCA9548A
What boards using the TCA9548A are built for
TCA9548A: common questions
Where can I find a TCA9548A reference design?
Each of the 12 boards on this page is a real design using the TCA9548A. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the TCA9548A SCL pin?
The SCL pin has a pull-up to 3.3V on 3 of 7 designs, most often 4.7 kΩ (then 2.2 kΩ). Counted from the KiCad layouts of 9 open source designs using the TCA9548A.
What pull-up resistor is used on the TCA9548A SDA pin?
The SDA pin has a pull-up to 3.3V on 3 of 7 designs, most often 4.7 kΩ (then 2.2 kΩ). Counted from the KiCad layouts of 9 open source designs using the TCA9548A.
What parts are used alongside the TCA9548A?
The ADS1256IDBR, AP2112K-1.8, BQ24075RGTR, BQ29700 and CH224K appear in the most repositories here.
Which microcontrollers do boards using the TCA9548A use?
Most are built on RP2040/RP2350 (4), ESP32 (2), Raspberry Pi (2) and AVR/Arduino (1).
How big is a typical board using the TCA9548A?
The median is 93.5 × 91 mm, and 58% are two-layer designs.
What is the most popular open source board using the TCA9548A?
By GitHub stars, Stm32pe midi by udu3324, with 35 stars.
Can I simulate one of these boards using the TCA9548A before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.