16 open source boards using the 68000D
Real designs built with the 68000D, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Raemixx500
SukkoPera
365.8 × 254 mm349 parts2LNo license313OpenAmiga500FastRamExpansion
SukkoPera
100 × 71.5 mm34 parts2LCustom license88Amiga-SMD-500
amigalisa
368.3 × 254 mm556 parts2LCERN-OHL-S-2.069ESP32
SF2000
jbilander
111.5 × 84 mm105 parts4LCC-BY-SA-4.032Yddraig
ddraig68k
340 × 210 mm214 parts4LMIT29FPGA
MigStorm-ITX
wiretap-retro
170 × 170 mm157 parts4LNo license26FPGA
M68k
annoyatron255
100 × 100 mm105 parts2LNo license24PistormTester
abrugsch
99.8 × 99.8 mm92 parts2LNo license1168k dev
maded2
190.5 × 158.4 mm81 parts2LApache-2.04M68KSnifferProbe
philpem
30.5 × 111.8 mm5 parts2LNo license3A500Sub
Bambelweeny57
365.8 × 254 mm344 parts2LNo license0MC68000
bobofet2-1
432.5 × 139 mm59 parts2LNo license0MC68000
ppsilv
257.6 × 228.4 mm58 parts2LGPL-3.00MC68000-first
bobofet2-1
255.3 × 176 mm59 parts2LNo license0NXP
MCL68
MicroCoreLabs
31.6 × 84.1 mm13 parts4LNo license532M68K-Nucleo
DaveRichmond
71.1 × 97.8 mm18 parts2LCustom license0
How designs wire the 68000D
Read from the KiCad layouts of 15 open source designs, one per repository: what each pin of the 68000D connects to, and the resistors, capacitors and other passives placed on it.
- The HALT pin has a pull-up to VCC on 7 of 15 designs, most often 4.7 kΩ (then 470 Ω).
- The RESET pin has a pull-up to VCC on 7 of 15 designs, most often 4.7 kΩ (then 10 kΩ).
- The VCC pins have a decoupling capacitor on 6 of 15 designs, most often 100 nF (then 330 nF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| BGACKpin 12 | Connected to: A connector 47% |
|
| BRpin 13 | Connected to: A connector 47% |
|
| VCCpin 14, 49 | Connected to: 5V 80% |
|
| GNDpin 16, 53 | Connected to: GND 93% | — |
| HALTpin 17 | Connected to: A connector 40% |
|
| RESETpin 18 | Connected to: A connector 27%, 74LS32 20% |
|
| VPApin 21 | Connected to: A connector 47% |
|
| IPL2pin 23 | Connected to: A connector 47% |
|
| IPL1pin 24 | Connected to: A connector 47% |
|
| IPL0pin 25 | Connected to: A connector 47% |
|
52 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include MCL68 by MicroCoreLabs, Raemixx500 by SukkoPera, OpenAmiga500FastRamExpansion by SukkoPera and Amiga-SMD-500 by amigalisa.
The 68000D in open source designs
The gallery holds 16 open source boards using the 68000D from 15 GitHub repositories; a typical one measures about 180.3 × 148.7 mm and carries around 87 components.
75% are two-layer designs, the rest use four layers or more, and 31% carry an open source license.
The most starred is MCL68 by MicroCoreLabs.
Parts used alongside the 68000D
What boards using the 68000D are built for
68000D: common questions
Where can I find a 68000D reference design?
Each of the 16 boards on this page is a real design using the 68000D. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the 68000D HALT pin?
The HALT pin has a pull-up to VCC on 7 of 15 designs, most often 4.7 kΩ (then 470 Ω). Counted from the KiCad layouts of 15 open source designs using the 68000D.
What pull-up resistor is used on the 68000D RESET pin?
The RESET pin has a pull-up to VCC on 7 of 15 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 15 open source designs using the 68000D.
What decoupling capacitors do designs use on the 68000D VCC pin?
The VCC pins have a decoupling capacitor on 6 of 15 designs, most often 100 nF (then 330 nF). Counted from the KiCad layouts of 15 open source designs using the 68000D.
What parts are used alongside the 68000D?
The 74LS245, 74LS32, 74LS05, 74LS157 and 74LS244 appear in the most repositories here.
Which microcontrollers do boards using the 68000D use?
Most are built on FPGA (2), ESP32 (1) and NXP (1).
How big is a typical board using the 68000D?
The median is 180.3 × 148.7 mm, and 75% are two-layer designs.
What is the most popular open source board using the 68000D?
By GitHub stars, MCL68 by MicroCoreLabs, with 532 stars.
Can I simulate one of these boards using the 68000D before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.