20 open source boards using the AP63200WU

Real designs built with the AP63200WU, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

20 boardsClear filters|Most starred

How designs wire the AP63200WU

Read from the KiCad layouts of 14 open source designs, one per repository: what each pin of the AP63200WU connects to, and the resistors, capacitors and other passives placed on it.

  • The FB pin has a resistor to GND on 14 of 14 designs, most often 62 kΩ (then 15 kΩ).
  • The SW pin has a inductor on 14 of 14 designs, most often 6.8 µH (then 10 µH).
  • The SW pin has a series capacitor on 14 of 14 designs, most often 100 nF.
  • The BST pin has a series capacitor on 14 of 14 designs, most often 100 nF.
FBpin 1Connected to: Signal 100%
  • Resistor to GND on 100% · 62 kΩ (5), 15 kΩ (1), 6.2 kΩ (1)
  • Pull-up to 3.3V on 64% · 182 kΩ (2), 270 kΩ (1), 18.2 kΩ (1)
  • Capacitor to the supply on 64% · 100 pF (5), 56 pF (2), 12 pF (1)
  • Series capacitor on 36% · 100 pF (3), 22 µF (2)
ENpin 2Connected to: VCC 64% · a signal 36%
INpin 3Connected to: VCC 64% · a signal 36%
GNDpin 4Connected to: GND 100%
SWpin 5Connected to: Signal 100%
  • Inductor on 100% · 6.8 µH (4), 10 µH (3), 2.2 µH (1)
  • Series capacitor on 100% · 100 nF (12)
BSTpin 6Connected to: Signal 100%
  • Series capacitor on 100% · 100 nF (12)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Power supply by sbstnh, Goatfc bones by Torie3, Frmw dcin by a-little-wifi and Projekt Mechatronik DC-AC by DriveLink-HM.

The AP63200WU in open source designs

The gallery holds 20 open source boards using the AP63200WU from 14 GitHub repositories; a typical one measures about 94.7 × 75.6 mm and carries around 97 components.

50% are two-layer designs, the rest use four layers or more, and 20% carry an open source license.

The most starred is Power supply by sbstnh.

Microcontrollers on boards using the AP63200WU

AP63200WU: common questions

Where can I find a AP63200WU reference design?

Each of the 20 boards on this page is a real design using the AP63200WU. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What resistor goes on the AP63200WU FB pin?

The FB pin has a resistor to GND on 14 of 14 designs, most often 62 kΩ (then 15 kΩ). Counted from the KiCad layouts of 14 open source designs using the AP63200WU.

How is the AP63200WU SW pin connected?

The SW pin has a inductor on 14 of 14 designs, most often 6.8 µH (then 10 µH). Counted from the KiCad layouts of 14 open source designs using the AP63200WU.

How is the AP63200WU BST pin connected?

The BST pin has a series capacitor on 14 of 14 designs, most often 100 nF. Counted from the KiCad layouts of 14 open source designs using the AP63200WU.

What parts are used alongside the AP63200WU?

The ESP32-S3-WROOM-1, ATmega328PB-A, ESP32-C6-WROOM-1U, FM24CL16B and LTV-357TB appear in the most repositories here.

Which microcontrollers do boards using the AP63200WU use?

Most are built on ESP32 (7), STM32 (7) and RP2040/RP2350 (1).

How big is a typical board using the AP63200WU?

The median is 94.7 × 75.6 mm, and 50% are two-layer designs.

What is the most popular open source board using the AP63200WU?

By GitHub stars, Power supply by sbstnh, with 64 stars.

Can I simulate one of these boards using the AP63200WU before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part