14 open source boards using the C5605

Real designs built with the C5605, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

14 boardsClear filters|Most starred

How designs wire the C5605

Read from the KiCad layouts of 10 open source designs, one per repository: what each pin of the C5605 connects to, and the resistors, capacitors and other passives placed on it.

  • The VCC pin has a decoupling capacitor on 6 of 10 designs, most often 100 nF (then 4.7 µF).
  • The 1Y pin has a series resistor on 5 of 10 designs, most often 150 Ω (then 620 Ω).
  • The 5Y pin is left unconnected on 6 of 10 designs (a signal on 3).
  • The 6Y pin is left unconnected on 6 of 10 designs (a signal on 3).
1Apin 1Connected to: A connector 30%, C7042 20%, the microcontroller 20%
  • Series resistor on 30% · 10 kΩ (2), 18 kΩ (1)
1Ypin 2Connected to: A connector 30%, the microcontroller 20%
  • Series resistor on 50% · 150 Ω (1), 620 Ω (1), 470 Ω (1)
3Apin 5Connected to: A connector 40% · GND 30%
  • Series resistor on 30% · 10 kΩ (2), 18 kΩ (1)
GNDpin 7Connected to: GND 100%
4Ypin 8Connected to: A connector 30%, the microcontroller 20% · not connected 30%
  • Series resistor on 30% · 470 Ω (1), 620 Ω (1), 5 kΩ (1)
4Apin 9Connected to: A connector 20% · GND 20% · VBUS 20%
  • Capacitor to GND on 30% · 100 nF (2), 1 µF (1)
  • Series resistor on 30% · 10 kΩ (2), 18 kΩ (1)
5Ypin 10Connected to: Not connected 60% · a signal 30%
6Ypin 12Connected to: Not connected 60% · a signal 30%
VCCpin 14Connected to: 3.3V 100%
  • Decoupling capacitor on 60% · 100 nF (6), 4.7 µF (1)

5 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Desktop 50 Pin TopConn by BlueSCSI, BonkDaddy2HP by shannon-greenlight, Centipede-32d by strickyak and Centipede-32d by strickyak.

The C5605 in open source designs

The gallery holds 14 open source boards using the C5605 from 10 GitHub repositories; a typical one measures about 97.6 × 93.5 mm and carries around 108 components.

64% use four copper layers or more, and 79% carry an open source license.

The most starred is Desktop 50 Pin TopConn by BlueSCSI.

Microcontrollers on boards using the C5605

C5605: common questions

Where can I find a C5605 reference design?

Each of the 14 boards on this page is a real design using the C5605. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What decoupling capacitors do designs use on the C5605 VCC pin?

The VCC pin has a decoupling capacitor on 6 of 10 designs, most often 100 nF (then 4.7 µF). Counted from the KiCad layouts of 10 open source designs using the C5605.

What resistor goes on the C5605 1Y pin?

The 1Y pin has a series resistor on 5 of 10 designs, most often 150 Ω (then 620 Ω). Counted from the KiCad layouts of 10 open source designs using the C5605.

How is the C5605 5Y pin connected?

The 5Y pin is left unconnected on 6 of 10 designs (a signal on 3). Counted from the KiCad layouts of 10 open source designs using the C5605.

What parts are used alongside the C5605?

The ADS1115IDGS, AMS1117-3.3_C347222, C14791, C427602 and C7042 appear in the most repositories here.

Which microcontrollers do boards using the C5605 use?

Most are built on RP2040/RP2350 (4), ESP32 (2), Raspberry Pi (1) and STM32 (1).

How big is a typical board using the C5605?

The median is 97.6 × 93.5 mm, and 36% are two-layer designs.

What is the most popular open source board using the C5605?

By GitHub stars, Desktop 50 Pin TopConn by BlueSCSI, with 457 stars.

Can I simulate one of these boards using the C5605 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part