10 open source boards using the INA186A3IDCKR
Real designs built with the INA186A3IDCKR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
OpenESC-20x20
OpenDrone-hw
31.2 × 33 mm180 parts6LCERN-OHL-S-2.0276VENDETTAESC
Caped-Crussader
40.5 × 43 mm222 parts6LCERN-OHL-S-2.028ESP32
OpenAIO
OpenDrone-hw
35 × 35 mm244 parts8LCERN-OHL-S-2.05ESP32
DrikrAIO
tetraethylmethane
50 × 50 mm339 parts6LNo license14in1-panel
OliviezGit
41.6 × 80.4 mm249 parts6LCERN-OHL-S-2.004in1
OpenDrone-hw
41.6 × 42.5 mm187 parts6LCERN-OHL-S-2.0834in1-panel
tetraethylmethane
41.6 × 80.4 mm249 parts6LNo license14in1
OliviezGit
41.6 × 42.5 mm207 parts6LCERN-OHL-S-2.00ESP32
OpenAIO
tetraethylmethane
35 × 35 mm244 parts8LNo license14in1
tetraethylmethane
41.6 × 42.5 mm187 parts6LNo license1
How designs wire the INA186A3IDCKR
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the INA186A3IDCKR connects to, and the resistors, capacitors and other passives placed on it.
- The VS_3 pin has a decoupling capacitor on 5 of 6 designs, most often 100 nF.
- The +IN_4 pin has a capacitor to GND on 5 of 6 designs, most often 100 nF (then 10 µF).
- The -IN_5 pin has a capacitor to GND on 5 of 6 designs, most often 10 µF (then 100 nF).
- The OUT_6 pin has a series resistor on 5 of 6 designs, most often 1 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| REF_1pin 1 | Connected to: GND 83% · a signal 17% | — |
| GND_2pin 2 | Connected to: GND 100% | — |
| VS_3pin 3 | Connected to: 3.3V 83% · a signal 17% |
|
| +IN_4pin 4 | Connected to: Signal 83% · BATT 17% |
|
| -IN_5pin 5 | Connected to: Signal 67% · GND 17% · BATT 17% |
|
| OUT_6pin 6 | Connected to: Signal 83% · 3.3V 17% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include OpenESC-20x20 by OpenDrone-hw, 4in1 by OpenDrone-hw, VENDETTAESC by Caped-Crussader and OpenAIO by OpenDrone-hw.
The INA186A3IDCKR in open source designs
The gallery holds 10 open source boards using the INA186A3IDCKR from 6 GitHub repositories; a typical one measures about 41.6 × 42.5 mm and carries around 233 components.
100% use four copper layers or more, and 60% carry an open source license.
The most starred is OpenESC-20x20 by OpenDrone-hw.
Parts used alongside the INA186A3IDCKR
Microcontrollers on boards using the INA186A3IDCKR
What boards using the INA186A3IDCKR are built for
INA186A3IDCKR: common questions
Where can I find a INA186A3IDCKR reference design?
Each of the 10 boards on this page is a real design using the INA186A3IDCKR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the INA186A3IDCKR VS_3 pin?
The VS_3 pin has a decoupling capacitor on 5 of 6 designs, most often 100 nF. Counted from the KiCad layouts of 6 open source designs using the INA186A3IDCKR.
How is the INA186A3IDCKR +IN_4 pin connected?
The +IN_4 pin has a capacitor to GND on 5 of 6 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 6 open source designs using the INA186A3IDCKR.
How is the INA186A3IDCKR -IN_5 pin connected?
The -IN_5 pin has a capacitor to GND on 5 of 6 designs, most often 10 µF (then 100 nF). Counted from the KiCad layouts of 6 open source designs using the INA186A3IDCKR.
What parts are used alongside the INA186A3IDCKR?
The AT32F421G8U7, NSG2065Q, TLV76733DRVR, FTC160808S4R7MBCA and LMR54406DBVR appear in the most repositories here.
Which microcontrollers do boards using the INA186A3IDCKR use?
Most are built on ESP32 (3).
How big is a typical board using the INA186A3IDCKR?
The median is 41.6 × 42.5 mm, and 0% are two-layer designs.
What is the most popular open source board using the INA186A3IDCKR?
By GitHub stars, OpenESC-20x20 by OpenDrone-hw, with 276 stars.
Can I simulate one of these boards using the INA186A3IDCKR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.