13 open source boards using the LMR54406DBVR
Real designs built with the LMR54406DBVR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
AxxSolder
AxxAxx
39 × 82.5 mm122 parts2LGPL-3.01.7kOpenESC-20x20
OpenDrone-hw
31.2 × 33 mm180 parts6LCERN-OHL-S-2.0276ESP32
Terrarium Control Board
justbuchanan
140 × 140 mm51 parts2LApache-2.02704in1-panel
OpenDrone-hw
41.6 × 80.4 mm249 parts6LCERN-OHL-S-2.083ESP32
Esptemp8c
gcormier
56.6 × 57.7 mm38 parts2LNo license8ESP32
DrikrAIO
tetraethylmethane
50 × 50 mm339 parts6LNo license14in1-panel
OliviezGit
41.6 × 80.4 mm249 parts6LCERN-OHL-S-2.00ESP32
N2k atom can485 hw
jtroyer76
32 × 64 mm28 parts2LCERN-OHL-S-2.00- schematic only · 122 partsSTM32
Kicad skidl assignment
rajsrivastava9801-blip
122 partsNo license0 4in1
OpenDrone-hw
41.6 × 42.5 mm187 parts6LCERN-OHL-S-2.0834in1-panel
tetraethylmethane
41.6 × 80.4 mm249 parts6LNo license14in1
OliviezGit
41.6 × 42.5 mm207 parts6LCERN-OHL-S-2.004in1
tetraethylmethane
41.6 × 42.5 mm187 parts6LNo license1
How designs wire the LMR54406DBVR
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the LMR54406DBVR connects to, and the resistors, capacitors and other passives placed on it.
- The CB_1 pin has a series capacitor on 8 of 8 designs, most often 100 nF.
- The FB_3 pin has a resistor to GND on 8 of 8 designs, most often 10 kΩ (then 22 kΩ).
- The FB_3 pin has a pull-up to 10V on 8 of 8 designs, most often 115 kΩ (then 360 kΩ).
- The SW_6 pin has a series capacitor on 8 of 8 designs, most often 100 nF.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| CB_1pin 1 | Connected to: Signal 100% |
|
| GND_2pin 2 | Connected to: GND 100% | — |
| FB_3pin 3 | Connected to: Signal 100% |
|
| EN_4pin 4 | Connected to: BATT 100% | — |
| VIN_5pin 5 | Connected to: BATT 100% |
|
| SW_6pin 6 | Connected to: FTC160808S4R7MBCA 50% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include AxxSolder by AxxAxx, OpenESC-20x20 by OpenDrone-hw, Terrarium Control Board by justbuchanan and 4in1 by OpenDrone-hw.
The LMR54406DBVR in open source designs
The gallery holds 13 open source boards using the LMR54406DBVR from 9 GitHub repositories; a typical one measures about 41.6 × 60.8 mm and carries around 187 components.
67% use four copper layers or more, and 62% carry an open source license.
The most starred is AxxSolder by AxxAxx.
Parts used alongside the LMR54406DBVR
What boards using the LMR54406DBVR are built for
LMR54406DBVR: common questions
Where can I find a LMR54406DBVR reference design?
Each of the 13 boards on this page is a real design using the LMR54406DBVR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the LMR54406DBVR CB_1 pin connected?
The CB_1 pin has a series capacitor on 8 of 8 designs, most often 100 nF. Counted from the KiCad layouts of 8 open source designs using the LMR54406DBVR.
What resistor goes on the LMR54406DBVR FB_3 pin?
The FB_3 pin has a resistor to GND on 8 of 8 designs, most often 10 kΩ (then 22 kΩ). Counted from the KiCad layouts of 8 open source designs using the LMR54406DBVR.
How is the LMR54406DBVR SW_6 pin connected?
The SW_6 pin has a series capacitor on 8 of 8 designs, most often 100 nF. Counted from the KiCad layouts of 8 open source designs using the LMR54406DBVR.
What parts are used alongside the LMR54406DBVR?
The TLV76733DRVR, AT32F421G8U7, FTC160808S4R7MBCA, INA186A3IDCKR and NSG2065Q appear in the most repositories here.
Which microcontrollers do boards using the LMR54406DBVR use?
Most are built on ESP32 (4) and STM32 (2).
How big is a typical board using the LMR54406DBVR?
The median is 41.6 × 60.8 mm, and 33% are two-layer designs.
What is the most popular open source board using the LMR54406DBVR?
By GitHub stars, AxxSolder by AxxAxx, with 1,714 stars.
Can I simulate one of these boards using the LMR54406DBVR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.