15 open source boards using the LM1881
Real designs built with the LM1881, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
RGB-to component
jamvanderloeff
50 × 70 mm58 parts2LMIT13Ti99-rgb
wiesl
99.1 × 66 mm79 parts2LNo license12PIC
Pictas
bigbass1997
74.9 × 89.2 mm34 parts2LNo license9Analog-Video-Comb-Filter
goscickiw
51.5 × 104.1 mm75 parts2LCC-BY-SA-4.08Microchip SAM
OSSW - Open Scart Switch - Main
BinaryS010
401.6 × 130.1 mm310 parts4LGPL-3.07SyncFix64
hackup
30.5 × 12.7 mm15 parts2LNo license7AVR/Arduino
Teletext decoder
avrovulcanxh607
119.4 × 116.8 mm74 parts2LNo license4Ta7357p
ldursw
23.5 × 8.4 mm13 parts6LMIT4Cvbs oscilloscope meter
harrypm
150.3 × 115.6 mm50 parts2LNo license1AVR/Arduino
AVML: PCB1 & PCB2
joem
37.5 × 100 mm74 parts2LNo license01802-Mini-9918-Video
dmadole
100 × 100 mm73 parts2LNo license0PICerino TMS9928
sparkletron
105.2 × 120.8 mm65 parts2LMIT0Z80VDP1A
lynchaj
100 × 100 mm90 parts2LNo license31Cvbs oscilloscope meter rounded
harrypm
52.2 × 113.8 mm50 parts2LNo license1ESP32
Vm129-cpu
mirdej
53.1 × 113.2 mm95 parts4LNo license23
How designs wire the LM1881
Read from the KiCad layouts of 14 open source designs, one per repository: what each pin of the LM1881 connects to, and the resistors, capacitors and other passives placed on it.
- The VIDEO pin has a series capacitor on 14 of 14 designs, most often 100 nF (then 47 nF).
- The INT pin has a resistor to GND on 14 of 14 designs, most often 680 kΩ.
- The INT pin has a capacitor to GND on 14 of 14 designs, most often 100 nF.
- The O/E pin is left unconnected on 12 of 14 designs (a signal on 2).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VIDEOpin 2 | Connected to: Signal 100% |
|
| GNDpin 4 | Connected to: GND 100% | — |
| BURSTpin 5 | Connected to: Not connected 64% · a signal 36% | — |
| INTpin 6 | Connected to: Signal 100% |
|
| O/Epin 7 | Connected to: Not connected 86% | — |
| VCCpin 8 | Connected to: VCC 100% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Z80VDP1A by lynchaj, Vm129-cpu by mirdej, RGB-to component by jamvanderloeff and Ti99-rgb by wiesl.
The LM1881 in open source designs
The gallery holds 15 open source boards using the LM1881 from 14 GitHub repositories; a typical one measures about 74.9 × 100 mm and carries around 73 components.
80% are two-layer designs, the rest use four layers or more, and 33% carry an open source license.
The most starred is Z80VDP1A by lynchaj.
Microcontrollers on boards using the LM1881
What boards using the LM1881 are built for
LM1881: common questions
Where can I find a LM1881 reference design?
Each of the 15 boards on this page is a real design using the LM1881. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the LM1881 VIDEO pin connected?
The VIDEO pin has a series capacitor on 14 of 14 designs, most often 100 nF (then 47 nF). Counted from the KiCad layouts of 14 open source designs using the LM1881.
What resistor goes on the LM1881 INT pin?
The INT pin has a resistor to GND on 14 of 14 designs, most often 680 kΩ. Counted from the KiCad layouts of 14 open source designs using the LM1881.
How is the LM1881 O/E pin connected?
The O/E pin is left unconnected on 12 of 14 designs (a signal on 2). Counted from the KiCad layouts of 14 open source designs using the LM1881.
What parts are used alongside the LM1881?
The L7805, THS7374, 4066, AD813 and TL081 appear in the most repositories here.
Which microcontrollers do boards using the LM1881 use?
Most are built on AVR/Arduino (2), ESP32 (1), PIC (1) and Microchip SAM (1).
How big is a typical board using the LM1881?
The median is 74.9 × 100 mm, and 80% are two-layer designs.
What is the most popular open source board using the LM1881?
By GitHub stars, Z80VDP1A by lynchaj, with 31 stars.
Can I simulate one of these boards using the LM1881 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.