8 open source boards using the LM2733XMF
Real designs built with the LM2733XMF, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
MegaMIDI
AidanHockey5
100 × 100 mm102 parts2LAGPL-3.0116AVR/Arduino
Genny
superjoebob
100 × 100 mm102 parts2LNo license92Microchip SAM
MegaBlaster2
AidanHockey5
99 × 99 mm102 parts4LAGPL-3.059Microchip SAM
YM2151 Arcade Classic 2
AidanHockey5
99 × 99 mm111 parts4LAGPL-3.022STM32
Alpha spectrometer v1
Maniak003
63.1 × 45 mm134 parts2LNo license0TUSS4470 shield
Neumi
69 × 53.8 mm38 parts2LNo license507STM32
Alpha spectrometer proto
Maniak003
54.6 × 21.5 mm85 parts2LNo license0TUSS4470 shield
kskwon02
69 × 53.8 mm38 parts2LNo license0
How designs wire the LM2733XMF
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the LM2733XMF connects to, and the resistors, capacitors and other passives placed on it.
- The SW_1 pin has a inductor on 7 of 7 designs, most often 10 µH (then 22 µH).
- The FB_3 pin has a series resistor on 7 of 7 designs, most often 51 kΩ (then 374 kΩ).
- The FB_3 pin has a resistor to GND on 7 of 7 designs, most often 12 kΩ (then 13.7 kΩ).
- The FB_3 pin has a series capacitor on 7 of 7 designs, most often 220 pF (then 47 pF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| SW_1pin 1 | Connected to: Signal 100% |
|
| GND_2pin 2 | Connected to: GND 100% | — |
| FB_3pin 3 | Connected to: Signal 100% |
|
| EN_4pin 4 | Connected to: Signal 71% · 5V 29% |
|
| VIN_5pin 5 | Connected to: VBUS 100% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include TUSS4470 shield by Neumi, MegaMIDI by AidanHockey5, Genny by superjoebob and MegaBlaster2 by AidanHockey5.
The LM2733XMF in open source designs
The gallery holds 8 open source boards using the LM2733XMF from 7 GitHub repositories; a typical one measures about 84 × 76.4 mm and carries around 102 components.
75% are two-layer designs, the rest use four layers or more, and 38% carry an open source license.
The most starred is TUSS4470 shield by Neumi.
Parts used alongside the LM2733XMF
Microcontrollers on boards using the LM2733XMF
What boards using the LM2733XMF are built for
LM2733XMF: common questions
Where can I find a LM2733XMF reference design?
Each of the 8 boards on this page is a real design using the LM2733XMF. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the LM2733XMF SW_1 pin connected?
The SW_1 pin has a inductor on 7 of 7 designs, most often 10 µH (then 22 µH). Counted from the KiCad layouts of 7 open source designs using the LM2733XMF.
What resistor goes on the LM2733XMF FB_3 pin?
The FB_3 pin has a series resistor on 7 of 7 designs, most often 51 kΩ (then 374 kΩ). Counted from the KiCad layouts of 7 open source designs using the LM2733XMF.
What decoupling capacitors do designs use on the LM2733XMF VIN_5 pin?
The VIN_5 pin has a decoupling capacitor on 7 of 7 designs, most often 10 µF. Counted from the KiCad layouts of 7 open source designs using the LM2733XMF.
What parts are used alongside the LM2733XMF?
The LD1117S33TR_SOT223, LD1117S50TR_SOT223, SN76489, YM2612 and 4050 appear in the most repositories here.
Which microcontrollers do boards using the LM2733XMF use?
Most are built on AVR/Arduino (2), Microchip SAM (2) and STM32 (2).
How big is a typical board using the LM2733XMF?
The median is 84 × 76.4 mm, and 75% are two-layer designs.
What is the most popular open source board using the LM2733XMF?
By GitHub stars, TUSS4470 shield by Neumi, with 507 stars.
Can I simulate one of these boards using the LM2733XMF before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.