50 open source boards using the H11L1
Real designs built with the H11L1, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
RP2040/RP2350
Pico dco
polykit
100 × 165 mm148 parts2LNo license161Raspberry Pi
Mt32-pi midi hat
chris-jh
64.3 × 56 mm22 parts2LGPL-3.0137AVR/Arduino
MegaMIDI
AidanHockey5
100 × 100 mm102 parts2LAGPL-3.0116AVR/Arduino
Genny
superjoebob
100 × 100 mm102 parts2LNo license92Minisynth32
grantek
51.3 × 96.2 mm30 parts2LCC-BY-SA-4.044STM32
Oscar components
dchwebb
71 × 100 mm63 parts4LUnlicense41Raspberry Pi
Minidexed
handeyeco
130.8 × 81.5 mm47 parts2LNo license23- schematic only · 22 partsRP2040/RP2350
Microgroove
afternoon
22 partsMIT21 - schematic only · 99 partsSTM32
Midimagic
herculesxe5
99 partsLGPL-3.014 STM32
MidiBox3
Dethernal
100 × 100 mm114 parts2LMIT5STM32
Asynth2Osc
everedero
83 × 106 mm204 parts4LGPL-3.04RISC-V
Kepler x
kunichiko
144 × 150 mm153 parts4LMIT4Gameport to midi
mlaux
47 × 61 mm11 parts2LGPL-3.04Seed3-DevKit-Pedal
daisyaudio
197 × 100 mm142 parts2LNo license3RP2040/RP2350
Midi controller
Tommie1236
100 × 100 mm515 parts4LCERN-OHL-W-2.02Seed3-DevKit-Desktop
daisyaudio
197 × 111 mm230 parts2LNo license2Seed3-DevKit-Eurorack
daisyaudio
141.9 × 128.5 mm130 parts2LNo license2AVR/Arduino
Electronic load
ondras12345
48.3 × 50.8 mm60 parts2LMIT2STM32
Drumboy Main
Randomwaves
268 × 152 mm345 parts4LMIT1Myo shield
Roboy
137.1 × 87 mm178 parts2LBSD-3-Clause1VAMP
syntonos
217.9 × 60 mm88 parts4LGPL-3.01RP2040/RP2350
Zero stomp
relic-se
85.2 × 98.9 mm80 parts2LGPL-3.01STM32
Asynth2osc
madees
69 × 106 mm194 parts4LGPL-3.00RP2040/RP2350
TaschenOper
davedarko
60 × 100 mm119 parts2LMIT0Deloop lite mk0
hmcty
178 × 83.3 mm84 parts4LMIT0STM32
Expresso
amonbenson
85.3 × 75.7 mm84 parts4LMIT0DaisyPatchSMThingie
Desval27
236.2 × 124.5 mm67 parts2LMIT0RP2040/RP2350
Console.placed
tomassasovsky
99.5 × 99.5 mm61 parts2LGPL-3.00DaisySeedThingie
Desval27
236.2 × 124.5 mm61 parts2LMIT0Mt32-cm3plus
peon374
76.2 × 104.1 mm60 parts2LNo license0MIDIController-IO-Boards
stefanhepp
150 × 100 mm47 parts2LCC-BY-SA-4.00Dimmer
drkntz
99.1 × 69.9 mm47 parts2LNo license0AVR/Arduino
Piano Lights
ddribin
98 × 51.6 mm36 parts2LMIT0Allosaurus footprint interactive
iwonder77
40 × 45 mm29 parts2LNo license0ESP32
Badascule bridge
teste80
80 × 50 mm28 parts2LCC-BY-NC-4.00NXP
Control rev3
PaulStoffregen
48.3 × 105.4 mm127 parts2LNo license160
How designs wire the H11L1
Read from the KiCad layouts of 42 open source designs, one per repository: what each pin of the H11L1 connects to, and the resistors, capacitors and other passives placed on it.
- The AN pin has a series resistor on 38 of 42 designs, most often 220 Ω (then 510 Ω).
- The VO pin has a pull-up to 3.3V on 33 of 42 designs, most often 270 Ω (then 470 Ω).
- The VCC pin has a decoupling capacitor on 18 of 42 designs, most often 100 nF (then 1 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| ANpin 1 | Connected to: Signal 98% |
|
| NCpin 3 | Connected to: Not connected 100% | — |
| VOpin 4 | Connected to: The microcontroller 43%, a connector 29% |
|
| GNDpin 5 | Connected to: GND 95% | — |
| VCCpin 6 | Connected to: 3.3V 88% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Many485 by eddyem, Pico dco by polykit, Control rev3 by PaulStoffregen and Mt32-pi midi hat by chris-jh.
The H11L1 in open source designs
The gallery holds 50 open source boards using the H11L1 from 43 GitHub repositories; a typical one measures about 98.5 × 99.2 mm and carries around 75 components.
75% are two-layer designs, the rest use four layers or more, and 66% carry an open source license.
The most starred is Many485 by eddyem.
Parts used alongside the H11L1
Microcontrollers on boards using the H11L1
What boards using the H11L1 are built for
H11L1: common questions
Where can I find a H11L1 reference design?
Each of the 50 boards on this page is a real design using the H11L1. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the H11L1 AN pin?
The AN pin has a series resistor on 38 of 42 designs, most often 220 Ω (then 510 Ω). Counted from the KiCad layouts of 42 open source designs using the H11L1.
What pull-up resistor is used on the H11L1 VO pin?
The VO pin has a pull-up to 3.3V on 33 of 42 designs, most often 270 Ω (then 470 Ω). Counted from the KiCad layouts of 42 open source designs using the H11L1.
What decoupling capacitors do designs use on the H11L1 VCC pin?
The VCC pin has a decoupling capacitor on 18 of 42 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 42 open source designs using the H11L1.
What parts are used alongside the H11L1?
The USBLC6-2SC6, TL072, Electrosmith_Daisy_Seed_Rev4, LD1117S50TR_SOT223 and LMR62421XMF appear in the most repositories here.
Which microcontrollers do boards using the H11L1 use?
Most are built on STM32 (11), RP2040/RP2350 (9), AVR/Arduino (4) and ESP32 (3).
How big is a typical board using the H11L1?
The median is 98.5 × 99.2 mm, and 75% are two-layer designs.
What is the most popular open source board using the H11L1?
By GitHub stars, Many485 by eddyem, with 208 stars.
Can I simulate one of these boards using the H11L1 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.