36 open source boards using the TL431LP
Real designs built with the TL431LP, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
RP2040/RP2350
GuitarPico
profdc9
100 × 100 mm127 parts2LNo license49RP2040/RP2350
TrebleSynth
profdc9
236 × 128 mm210 parts2LNo license11- schematic only · 102 parts
Eurorack-PT2399-Delay
DIYSynthMNL
102 partsNo license10 Sincos interpolator
finngineering
100 × 50 mm57 parts2LMIT5Bluepill design
thesunRider
83.5 × 95.5 mm66 parts2LMIT3Placa buck
fadelrio
126 × 66.5 mm52 parts2LNo license3ESP32
Dc load
Fyfar
166.4 × 70.3 mm50 parts2LNo license2RP2040/RP2350
TrebleSynth
sinitsinmike
236 × 128 mm210 parts2LNo license1Nb1ecu
swagprincess
154 × 159 mm119 parts4LGPL-3.01Auto-SMPS
Shreyas-k-p
281.3 × 131.5 mm93 parts2LNo license1AVR/Arduino
Battery capacity meter
ikatkov
100 × 99.9 mm68 parts2LNo license1Buck
fberni21
88.4 × 81 mm68 parts2LNo license1Dual power supply
amitesh-singh
172.5 × 96.2 mm27 parts2LGPL-3.01Psu2psu01
minamonra
142 × 78 mm126 parts2LNo license0AVR/Arduino
Tarpn battery backup deluxe
tarpn
127 × 76.2 mm85 parts2LNo license0NXP
Exoskeleton
Bihyungbetter
114.3 × 134.5 mm55 parts4LNo license0Buck realimentada2
Balta-Etche-FIUBA
95 × 89 mm54 parts2LNo license0Blr
0x007E
106 × 50 mm41 parts2LCC-BY-NC-4.00Sapflux heater
Coweeta
38.1 × 63.5 mm37 parts2LNo license0AVR/Arduino
PCB Christmas Tree
reivax-boucoi
88.7 × 98 mm35 parts2LGPL-3.00AVR/Arduino
Rarara
knx444
90 × 100 mm34 parts2LNo license0Double electronic load
virtual-machinist
49.1 × 51.1 mm33 parts2LCC-BY-SA-4.00- schematic only · 84 partsESP32
Esp32-olcum karti
Muhammet933321
84 partsMIT0 PIC
Bidirectional Power Converter 24V-12V with BMS
kwiecinski
99.5 × 99.5 mm156 parts2LMIT3AVR/Arduino
328p design
thesunRider
76 × 88 mm51 parts2LMIT3Fuente
fberni21
64.4 × 41.1 mm39 parts2LNo license1Protection
aykutozdemir
65 × 80 mm69 parts2LNo license0Regulador Lineal
Balta-Etche-FIUBA
64 × 51 mm27 parts2LNo license0Carga activa
fberni21
73.5 × 40.3 mm33 parts2LNo license1Transistor
apxco
152.4 × 76.2 mm115 parts2LNo license0Buck
Seba-SL
106.5 × 67.5 mm28 parts2LNo license0Current Sensor
aykutozdemir
60 × 40 mm19 parts2LNo license0PIC
Misc
kwiecinski
99.5 × 99.5 mm152 parts2LMIT3Pwm
fberni21
43.9 × 54.9 mm22 parts2LNo license1Comparador
PappasFlow
79.5 × 79 mm39 parts2LNo license0Constant Current Sink Test
sdp8483
19.4 × 43.9 mm8 parts2LMIT0
How designs wire the TL431LP
Read from the KiCad layouts of 27 open source designs, one per repository: what each pin of the TL431LP connects to, and the resistors, capacitors and other passives placed on it.
- The A pin is tied to GND on 22 of 27 designs (a signal on 4).
- The REF pin has a series resistor on 18 of 27 designs, most often 1 kΩ (then 10 kΩ).
- The K pin has a series resistor on 17 of 27 designs, most often 1 kΩ (then 10 kΩ).
- The K pin has a pull-up to 5V on 13 of 27 designs, most often 1 kΩ (then 10 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| REFpin 1 | Connected to: Signal 96% |
|
| Apin 2 | Connected to: GND 81% | — |
| Kpin 3 | Connected to: Signal 81% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include GuitarPico by profdc9, TrebleSynth by profdc9, Sincos interpolator by finngineering and Placa buck by fadelrio.
The TL431LP in open source designs
The gallery holds 36 open source boards using the TL431LP from 29 GitHub repositories; a typical one measures about 99.5 × 79.5 mm and carries around 55 components.
94% are two-layer designs, the rest use four layers or more, and 31% carry an open source license.
The most starred is GuitarPico by profdc9.
Parts used alongside the TL431LP
Microcontrollers on boards using the TL431LP
What boards using the TL431LP are built for
TL431LP: common questions
Where can I find a TL431LP reference design?
Each of the 36 boards on this page is a real design using the TL431LP. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the TL431LP A pin connected?
The A pin is tied to GND on 22 of 27 designs (a signal on 4). Counted from the KiCad layouts of 27 open source designs using the TL431LP.
What resistor goes on the TL431LP REF pin?
The REF pin has a series resistor on 18 of 27 designs, most often 1 kΩ (then 10 kΩ). Counted from the KiCad layouts of 27 open source designs using the TL431LP.
What resistor goes on the TL431LP K pin?
The K pin has a series resistor on 17 of 27 designs, most often 1 kΩ (then 10 kΩ). Counted from the KiCad layouts of 27 open source designs using the TL431LP.
What parts are used alongside the TL431LP?
The LM358, LM7805_TO220, L7805, PC817 and TL072 appear in the most repositories here.
Which microcontrollers do boards using the TL431LP use?
Most are built on AVR/Arduino (5), RP2040/RP2350 (3), ESP32 (2) and PIC (2).
How big is a typical board using the TL431LP?
The median is 99.5 × 79.5 mm, and 94% are two-layer designs.
What is the most popular open source board using the TL431LP?
By GitHub stars, GuitarPico by profdc9, with 49 stars.
Can I simulate one of these boards using the TL431LP before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.