11 open source boards using the MCP1702
Real designs built with the MCP1702, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
TI MSP430/CC
Apimote
riverloopsec
83.3 × 33.4 mm80 parts4LTAPR-OHL-1.089AVR/Arduino
RS485 Soil moisture sensor
Miceuz
18 × 149 mm29 parts4LApache-2.073PIC
EkoPuszka
media3-0
72.4 × 45.7 mm75 parts2LMIT0RP2040/RP2350
Mico
Mentra-Community
30.5 × 138 mm61 parts2LMIT1.2kAVR/Arduino
Rs485-moist sensor pannel
Miceuz
5 × 149.5 mm29 parts2LApache-2.073RP2040/RP2350
Msa
Mentra-Community
47.8 × 9.4 mm53 parts2LMIT1.2kMicrophone
Mentra-Community
5.5 × 6.1 mm6 parts2LMIT1.2kSTM32
Brushless board
robotronik
60 × 62.5 mm57 parts2LNo license1STM32
Brushless board
robotronik
60 × 62.5 mm57 parts2LNo license1Cb minibat chipant
panStamp
25.4 × 56.6 mm29 partsGPL-2.015Minibat carrier board for panStamp
panStamp
25.4 × 55.8 mm29 partsGPL-2.015
How designs wire the MCP1702
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the MCP1702 connects to, and the resistors, capacitors and other passives placed on it.
- Pin 3 has a decoupling capacitor on 6 of 6 designs, most often 1 µF (then 10 µF).
- Pin 1 is tied to GND on 6 of 6 designs.
- Pin 2 has a decoupling capacitor on 5 of 6 designs, most often 1 µF (then 100 nF).
- Pin 2 is tied to 3.3V on 5 of 6 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: GND 100% | — |
| Pin 2 | Connected to: 3.3V 83% · a signal 17% |
|
| Pin 3 | Connected to: 3.3V 67% · a signal 33% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Mico by Mentra-Community, Apimote by riverloopsec, RS485 Soil moisture sensor by Miceuz and Cb minibat chipant by panStamp.
The MCP1702 in open source designs
The gallery holds 11 open source boards using the MCP1702 from 7 GitHub repositories; a typical one measures about 30.5 × 56.6 mm and carries around 53 components.
78% are two-layer designs, the rest use four layers or more, and 82% carry an open source license.
The most starred is Mico by Mentra-Community.
Parts used alongside the MCP1702
Microcontrollers on boards using the MCP1702
What boards using the MCP1702 are built for
MCP1702: common questions
Where can I find a MCP1702 reference design?
Each of the 11 boards on this page is a real design using the MCP1702. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the MCP1702 pin 3?
Pin 3 has a decoupling capacitor on 6 of 6 designs, most often 1 µF (then 10 µF). Counted from the KiCad layouts of 7 open source designs using the MCP1702.
How is the MCP1702 pin 1 connected?
Pin 1 is tied to GND on 6 of 6 designs. Counted from the KiCad layouts of 7 open source designs using the MCP1702.
What decoupling capacitors do designs use on the MCP1702 pin 2?
Pin 2 has a decoupling capacitor on 5 of 6 designs, most often 1 µF (then 100 nF). Counted from the KiCad layouts of 7 open source designs using the MCP1702.
What parts are used alongside the MCP1702?
The 12v input, 5v input, DEC24/2, MCP2562 and STM32F042K6TX appear in the most repositories here.
Which microcontrollers do boards using the MCP1702 use?
Most are built on AVR/Arduino (2), RP2040/RP2350 (2), STM32 (2) and PIC (1).
How big is a typical board using the MCP1702?
The median is 30.5 × 56.6 mm, and 78% are two-layer designs.
What is the most popular open source board using the MCP1702?
By GitHub stars, Mico by Mentra-Community, with 1,235 stars.
Can I simulate one of these boards using the MCP1702 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.