19 open source boards using the MCP34119P

Real designs built with the MCP34119P, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

19 boardsClear filters|Most starred

How designs wire the MCP34119P

Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the MCP34119P connects to, and the resistors, capacitors and other passives placed on it.

  • The FC2 pin has a capacitor to GND on 5 of 7 designs, most often 4.7 µF (then 5 µF).
  • The FC1 pin has a capacitor to GND on 5 of 7 designs, most often 1 µF.
  • The VIN pin has a series resistor on 5 of 7 designs, most often 20 kΩ (then 10 kΩ).
  • The VO1 pin has a series resistor on 5 of 7 designs, most often 10 kΩ (then 20 kΩ).
CDpin 1Connected to: GND 71% · a signal 29%
FC2pin 2Connected to: Signal 71% · 3.3V 29%
  • Capacitor to GND on 71% · 4.7 µF (4), 5 µF (1)
FC1pin 3Connected to: Signal 71% · not connected 29%
  • Capacitor to GND on 71% · 1 µF (5)
VINpin 4Connected to: Signal 71% · not connected 29%
  • Series resistor on 71% · 20 kΩ (4), 10 kΩ (4), 110 kΩ (1)
VO1pin 5Connected to: A connector 57% · not connected 29%
  • Series resistor on 71% · 10 kΩ (3), 20 kΩ (1), 110 kΩ (1)
VCCpin 6Connected to: 5V 71% · a signal 29%
GNDpin 7Connected to: GND 71% · a signal 29%

1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include CrickHit by devanshjoshi08, ECE445L Operator Final by Andres-Wearden, SeniorDesign SwanGanz by ATK-1 and ECE 445L Baseline Project by mjetpurwala.

The MCP34119P in open source designs

The gallery holds 19 open source boards using the MCP34119P from 14 GitHub repositories; a typical one measures about 114.3 × 88.9 mm and carries around 40 components.

95% are two-layer designs, the rest use four layers or more, and 5% carry an open source license.

The most starred is CrickHit by devanshjoshi08.

Microcontrollers on boards using the MCP34119P

What boards using the MCP34119P are built for

MCP34119P: common questions

Where can I find a MCP34119P reference design?

Each of the 19 boards on this page is a real design using the MCP34119P. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the MCP34119P FC2 pin connected?

The FC2 pin has a capacitor to GND on 5 of 7 designs, most often 4.7 µF (then 5 µF). Counted from the KiCad layouts of 7 open source designs using the MCP34119P.

How is the MCP34119P FC1 pin connected?

The FC1 pin has a capacitor to GND on 5 of 7 designs, most often 1 µF. Counted from the KiCad layouts of 7 open source designs using the MCP34119P.

What resistor goes on the MCP34119P VIN pin?

The VIN pin has a series resistor on 5 of 7 designs, most often 20 kΩ (then 10 kΩ). Counted from the KiCad layouts of 7 open source designs using the MCP34119P.

What parts are used alongside the MCP34119P?

The LP-MSPM0G3507, Adafruit ST7735R, HiLetGo_ST7735R, LM4041CILPR and EK-TM4C123GXL appear in the most repositories here.

Which microcontrollers do boards using the MCP34119P use?

Most are built on ESP8266 (4) and ESP32 (2).

How big is a typical board using the MCP34119P?

The median is 114.3 × 88.9 mm, and 95% are two-layer designs.

What is the most popular open source board using the MCP34119P?

By GitHub stars, CrickHit by devanshjoshi08, with 1 stars.

Can I simulate one of these boards using the MCP34119P before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part