19 open source boards using the OP07

Real designs built with the OP07, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

19 boardsClear filters|Most starred

How designs wire the OP07

Read from the KiCad layouts of 17 open source designs, one per repository: what each pin of the OP07 connects to, and the resistors, capacitors and other passives placed on it.

  • The - pin has a series resistor on 13 of 17 designs, most often 10 kΩ (then 100 kΩ).
  • Pin 6 has a series resistor on 13 of 17 designs, most often 10 kΩ (then 0 Ω).
  • The VOS pins is left unconnected on 82% of them (a signal on 6).
  • Pin 6 has a series capacitor on 7 of 17 designs, most often 4.7 µF (then 220 nF).
VOSpin 1, 8Connected to: Not connected 82% · a signal 18%
-pin 2Connected to: Signal 94%
  • Series resistor on 76% · 10 kΩ (7), 100 kΩ (3), 20 kΩ (2)
  • Series capacitor on 35% · 100 nF (2), 10 nF (2), 1 nF (1)
NCpin 5Connected to: Not connected 100%
Pin 6Connected to: A connector 24%
  • Series resistor on 76% · 10 kΩ (9), 0 Ω (3), 100 kΩ (2)
  • Series capacitor on 41% · 4.7 µF (1), 220 nF (1), 1 nF (1)
V+pin 7Connected to: 15V 82% · a signal 18%
  • Decoupling capacitor on 35% · 100 nF (3), 470 nF (1), 1 µF (1)

2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Entry afe characterization by azonenberg, Smu main 1 by jaromir-sukuba, EV Charger by fotherja and VCF Diode Ladder Filter by mzuelch.

The OP07 in open source designs

The gallery holds 19 open source boards using the OP07 from 17 GitHub repositories; a typical one measures about 98.4 × 83.7 mm and carries around 73 components.

84% are two-layer designs, the rest use four layers or more, and 58% carry an open source license.

The most starred is Entry afe characterization by azonenberg.

Parts used alongside the OP07

Microcontrollers on boards using the OP07

OP07: common questions

Where can I find a OP07 reference design?

Each of the 19 boards on this page is a real design using the OP07. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What resistor goes on the OP07 - pin?

The - pin has a series resistor on 13 of 17 designs, most often 10 kΩ (then 100 kΩ). Counted from the KiCad layouts of 17 open source designs using the OP07.

What resistor goes on the OP07 pin 6?

Pin 6 has a series resistor on 13 of 17 designs, most often 10 kΩ (then 0 Ω). Counted from the KiCad layouts of 17 open source designs using the OP07.

How is the OP07 VOS pin connected?

The VOS pins is left unconnected on 82% of them (a signal on 6). Counted from the KiCad layouts of 17 open source designs using the OP07.

What parts are used alongside the OP07?

The LM358, DG411xY, LM324 and LM399 appear in the most repositories here.

Which microcontrollers do boards using the OP07 use?

Most are built on AVR/Arduino (5), NXP (1), PIC (1) and STM32 (1).

How big is a typical board using the OP07?

The median is 98.4 × 83.7 mm, and 84% are two-layer designs.

What is the most popular open source board using the OP07?

By GitHub stars, Entry afe characterization by azonenberg, with 193 stars.

Can I simulate one of these boards using the OP07 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part