13 open source boards using the OPA350
Real designs built with the OPA350, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Tako
ssbb
230.7 × 97.8 mm76 parts4LMIT197STM32
Travaulta WKL
calvin-mcd
208.3 × 75.8 mm46 parts4LCC-BY-NC-4.016AVR/Arduino
UltrasonicSystem
Sonicators
145 × 110 mm81 parts2LNo license15NXP
Motor high current sensors
jonblissett
182.8 × 54 mm221 parts2LGPL-3.011STM32
The nicholas van prototype
calvin-mcd
242.9 × 95.3 mm58 parts4LCC-BY-NC-4.02AVR/Arduino
Peripheral board
Lintaroh
165 × 135 mm145 parts2LMIT0AVR/Arduino
GlazerLab KStat
nfroehberg
139.7 × 41.9 mm116 parts2LNo license0YETI60
wZuck
285 × 94.6 mm77 parts4LNo license0STM32
Analog dithering
Luk9091
55 × 30 mm58 parts4LNo license0STM32
EC60 origin
vadikgo
285 × 94.6 mm51 parts4LMIT0STM32
Travaulta HHKB
calvin-mcd
209.7 × 76.4 mm45 parts4LCC-BY-NC-4.016STM32
The nicholas van revision
calvin-mcd
242.9 × 95.3 mm54 parts4LCC-BY-NC-4.02Optical digitizer
jrleeman
114.3 × 33 mm21 parts4LNo license0
How designs wire the OPA350
Read from the KiCad layouts of 11 open source designs, one per repository: what each pin of the OPA350 connects to, and the resistors, capacitors and other passives placed on it.
- The V- pin is tied to GND on 11 of 11 designs.
- The OUT pin has a series resistor on 9 of 11 designs, most often 100 kΩ (then 5.1 kΩ).
- The V+ pin has a decoupling capacitor on 9 of 11 designs, most often 100 nF (then 1 µF).
- The NULL pins is left unconnected on 91% of them (a signal on 2).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| NULLpin 1, 5 | Connected to: Not connected 91% | — |
| IN-pin 2 | Connected to: Signal 91% |
|
| IN+pin 3 | Connected to: 74HC4051 45%, the microcontroller 36% |
|
| V-pin 4 | Connected to: GND 100% | — |
| OUTpin 6 | Connected to: The microcontroller 36% |
|
| V+pin 7 | Connected to: VBAT 82% · a signal 18% |
|
| NCpin 8 | Connected to: Not connected 91% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Tako by ssbb, Travaulta HHKB by calvin-mcd, UltrasonicSystem by Sonicators and Motor high current sensors by jonblissett.
The OPA350 in open source designs
The gallery holds 13 open source boards using the OPA350 from 11 GitHub repositories; a typical one measures about 208.3 × 94.6 mm and carries around 58 components.
69% use four copper layers or more, and 31% carry an open source license.
The most starred is Tako by ssbb.
Parts used alongside the OPA350
Microcontrollers on boards using the OPA350
What boards using the OPA350 are built for
OPA350: common questions
Where can I find a OPA350 reference design?
Each of the 13 boards on this page is a real design using the OPA350. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the OPA350 V- pin connected?
The V- pin is tied to GND on 11 of 11 designs. Counted from the KiCad layouts of 11 open source designs using the OPA350.
What resistor goes on the OPA350 OUT pin?
The OUT pin has a series resistor on 9 of 11 designs, most often 100 kΩ (then 5.1 kΩ). Counted from the KiCad layouts of 11 open source designs using the OPA350.
What decoupling capacitors do designs use on the OPA350 V+ pin?
The V+ pin has a decoupling capacitor on 9 of 11 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 11 open source designs using the OPA350.
What parts are used alongside the OPA350?
The 74HC4051, STM32F401CBUx and XC6206PXXXMR appear in the most repositories here.
Which microcontrollers do boards using the OPA350 use?
Most are built on STM32 (7), AVR/Arduino (3) and NXP (1).
How big is a typical board using the OPA350?
The median is 208.3 × 94.6 mm, and 31% are two-layer designs.
What is the most popular open source board using the OPA350?
By GitHub stars, Tako by ssbb, with 197 stars.
Can I simulate one of these boards using the OPA350 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.