21 open source boards using the TMUX1511PWR
Real designs built with the TMUX1511PWR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
RP2040/RP2350
SWD2USBC Sample Target
alvarop
51.8 × 20 mm47 parts4LCC0-1.029KevinbotV3
meowmeowahr
156.5 × 85.4 mm152 parts4LCERN-OHL-S-2.07ESP32
Chatgpt astra test2
fredriknk
100 × 80 mm90 parts4LMIT3STM32
Hub
Bruhdows
148 × 78 mm309 parts4LNo license1ESP32
Chainaxe
johnny9
100 × 70 mm109 parts4LCERN-OHL-S-2.01Raspberry Pi
Iasis
hydazz
130 × 100 mm636 parts6LApache-2.00ESP32
Assembly preview
ripclap
110 × 96 mm423 parts6LCERN-OHL-P-2.00STM32
Flight-Controller-V1
desanv01
104 × 104 mm310 parts6LCustom license0Kevinbot core
Kevinbot-Robotics
156.5 × 85.4 mm152 parts4LCERN-OHL-S-2.00Crab robot
triluongmh-byte
110 × 80 mm113 parts4LNo license0Assembly source
zcrawling
65 × 56 mm65 parts4LNo license0STM32
Debugotron - SWD Sample Target
alvarop
39.7 × 14 mm30 parts2LBSD-3-Clause52WCH CH32/CH55x
Tile
Bruhdows
68 × 68 mm109 parts4LNo license1ESP32
Carrier
ripclap
110 × 96 mm423 parts6LCERN-OHL-P-2.00First route
zcrawling
65 × 56 mm65 parts4LNo license0ESP32
Alec sensor
eshelton328
64 × 56 mm88 parts4LNo license0ESP32
Alec sensor
eshelton328
64 × 56 mm88 parts4LNo license0Prelayout b2
zcrawling
65 × 56 mm65 parts4LNo license0Rbphat
zcrawling
65 × 56 mm65 parts4LNo license0Seeded labelled
zcrawling
65 × 56 mm65 parts4LNo license0ESP32
ARDF-TX UNIVERSAL CONTROLLER
DD1SB
100 × 100 mm197 parts2LMIT0
How designs wire the TMUX1511PWR
Read from the KiCad layouts of 15 open source designs, one per repository: what each pin of the TMUX1511PWR connects to, and the resistors, capacitors and other passives placed on it.
- The VDD pin has a decoupling capacitor on 12 of 15 designs, most often 100 nF (then 1 µF).
- The S1 pin has a series resistor on 8 of 15 designs, most often 180 kΩ (then 1 kΩ).
- The S2 pin has a resistor to GND on 7 of 15 designs, most often 10 kΩ (then 100 kΩ).
- The S3 pin has a resistor to GND on 7 of 15 designs, most often 10 kΩ (then 100 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| SEL1pin 1 | Connected to: The microcontroller 27%, TMUX1511PWR 20% |
|
| S1pin 2 | Connected to: The microcontroller 27%, a connector 20% |
|
| SEL2pin 4 | Connected to: The microcontroller 27%, TMUX1511PWR 20% |
|
| S2pin 5 | Connected to: The microcontroller 27% |
|
| GNDpin 7 | Connected to: GND 100% | — |
| S3pin 9 | Connected to: A connector 20%, the microcontroller 20% |
|
| VDDpin 14 | Connected to: 3.3V 53% · a signal 47% |
|
7 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Debugotron - SWD Sample Target by alvarop, SWD2USBC Sample Target by alvarop, KevinbotV3-KiCAD by meowmeowahr and Chatgpt astra test2 by fredriknk.
The TMUX1511PWR in open source designs
The gallery holds 21 open source boards using the TMUX1511PWR from 15 GitHub repositories; a typical one measures about 100 × 70 mm and carries around 109 components.
90% use four copper layers or more, and 48% carry an open source license.
The most starred is Debugotron - SWD Sample Target by alvarop.
Parts used alongside the TMUX1511PWR
Microcontrollers on boards using the TMUX1511PWR
What boards using the TMUX1511PWR are built for
TMUX1511PWR: common questions
Where can I find a TMUX1511PWR reference design?
Each of the 21 boards on this page is a real design using the TMUX1511PWR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the TMUX1511PWR VDD pin?
The VDD pin has a decoupling capacitor on 12 of 15 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 15 open source designs using the TMUX1511PWR.
What resistor goes on the TMUX1511PWR S1 pin?
The S1 pin has a series resistor on 8 of 15 designs, most often 180 kΩ (then 1 kΩ). Counted from the KiCad layouts of 15 open source designs using the TMUX1511PWR.
What resistor goes on the TMUX1511PWR S2 pin?
The S2 pin has a resistor to GND on 7 of 15 designs, most often 10 kΩ (then 100 kΩ). Counted from the KiCad layouts of 15 open source designs using the TMUX1511PWR.
What parts are used alongside the TMUX1511PWR?
The USBLC6-2SC6, ADS1115IDGSR, SN74LVC1G04DBVR, TPS259470LRPWR and TPS26600PWPR appear in the most repositories here.
Which microcontrollers do boards using the TMUX1511PWR use?
Most are built on ESP32 (7), STM32 (3), WCH CH32/CH55x (1) and Raspberry Pi (1).
How big is a typical board using the TMUX1511PWR?
The median is 100 × 70 mm, and 10% are two-layer designs.
What is the most popular open source board using the TMUX1511PWR?
By GitHub stars, Debugotron - SWD Sample Target by alvarop, with 52 stars.
Can I simulate one of these boards using the TMUX1511PWR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.