21 open source boards using the 24LC64

Real designs built with the 24LC64, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

21 boardsClear filters|Most starred

How designs wire the 24LC64

Read from the KiCad layouts of 17 open source designs, one per repository: what each pin of the 24LC64 connects to, and the resistors, capacitors and other passives placed on it.

  • The A1 pin is tied to GND on 16 of 17 designs.
  • The A0 pin is tied to GND on 15 of 17 designs.
  • The A2 pin is tied to GND on 14 of 17 designs (not connected on 2).
  • The WP pin is tied to GND on 12 of 16 designs (not connected on 2, a signal on 2).
A0pin 1Connected to: GND 88%
A1pin 2Connected to: GND 94%
A2pin 3Connected to: GND 82%
GNDpin 4Connected to: GND 94%
SDApin 5Connected to: A connector 59%, the microcontroller 59%
  • Pull-up to 3.3V on 53% · 4.7 kΩ (8), 2 kΩ (1)
SCLpin 6Connected to: A connector 63%, the microcontroller 56%
  • Pull-up to 3.3V on 50% · 4.7 kΩ (7), 2 kΩ (1)
WPpin 7Connected to: GND 75%
VCCpin 8Connected to: 3.3V 88%
  • Decoupling capacitor on 63% · 100 nF (12)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Switch board by FOSDEM, Overnumpad controller 1xb by purdeaandrei, Eurorack spinfx by grappendorf and Jones by jpskenn.

The 24LC64 in open source designs

The gallery holds 21 open source boards using the 24LC64 from 18 GitHub repositories; a typical one measures about 100 × 89.5 mm and carries around 124 components.

80% are two-layer designs, the rest use four layers or more, and 52% carry an open source license.

The most starred is Switch board by FOSDEM.

24LC64: common questions

Where can I find a 24LC64 reference design?

Each of the 21 boards on this page is a real design using the 24LC64. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the 24LC64 A1 pin connected?

The A1 pin is tied to GND on 16 of 17 designs. Counted from the KiCad layouts of 17 open source designs using the 24LC64.

How is the 24LC64 A0 pin connected?

The A0 pin is tied to GND on 15 of 17 designs. Counted from the KiCad layouts of 17 open source designs using the 24LC64.

How is the 24LC64 A2 pin connected?

The A2 pin is tied to GND on 14 of 17 designs (not connected on 2). Counted from the KiCad layouts of 17 open source designs using the 24LC64.

What parts are used alongside the 24LC64?

The ATMEGA32U4-MU, L7805, LM386, NCP1117ST33T3G and NE5532 appear in the most repositories here.

Which microcontrollers do boards using the 24LC64 use?

Most are built on ESP32 (4), AVR/Arduino (4), STM32 (3) and RP2040/RP2350 (2).

How big is a typical board using the 24LC64?

The median is 100 × 89.5 mm, and 80% are two-layer designs.

What is the most popular open source board using the 24LC64?

By GitHub stars, Switch board by FOSDEM, with 114 stars.

Can I simulate one of these boards using the 24LC64 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part