30 open source boards using the ESP32-S3-WROOM-1U

Real designs built with the ESP32-S3-WROOM-1U, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

30 boardsClear filters|Most starred

How designs wire the ESP32-S3-WROOM-1U

Read from the KiCad layouts of 20 open source designs, one per repository: what each pin of the ESP32-S3-WROOM-1U connects to, and the resistors, capacitors and other passives placed on it.

  • The EN pin has a pull-up to 3.3V on 19 of 20 designs, most often 10 kΩ (then 4.7 kΩ).
  • The EN pin has a capacitor to GND on 17 of 20 designs, most often 1 µF (then 100 nF).
  • The 3V3 pin is tied to 3.3V on 19 of 20 designs.
  • The IO35 pin is left unconnected on 18 of 20 designs (a signal on 2).
GNDpin 1, 40, 41Connected to: GND 95%
3V3pin 2Connected to: 3.3V 95%
ENpin 3Connected to: A connector 25%
  • Pull-up to 3.3V on 95% · 10 kΩ (17), 4.7 kΩ (1), 603 Ω (1)
  • Capacitor to GND on 85% · 1 µF (14), 100 nF (7)
IO46pin 16Connected to: Not connected 75% · a signal 25%
IO45pin 26Connected to: Not connected 70% · a signal 30%
IO0pin 27Connected to: A connector 25%
  • Pull-up to 3.3V on 50% · 10 kΩ (7), 4.7 kΩ (1), 603 Ω (1)
IO35pin 28Connected to: Not connected 90%
IO36pin 29Connected to: Not connected 85% · a signal 15%
IO37pin 30Connected to: Not connected 90%

30 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include PCBA-KNOT by intechstudio, Sonatino by luminationlabs, MIDAS MK1 by ISSUIUC and ESP32 CSI WIFI NODE by swayerloren.

The ESP32-S3-WROOM-1U in open source designs

The gallery holds 30 open source boards using the ESP32-S3-WROOM-1U from 20 GitHub repositories; a typical one measures about 67.5 × 60 mm and carries around 49 components.

53% use four copper layers or more, and 20% carry an open source license.

The most starred is PCBA-KNOT by intechstudio.

Parts used alongside the ESP32-S3-WROOM-1U

Microcontrollers on boards using the ESP32-S3-WROOM-1U

ESP32-S3-WROOM-1U: common questions

Where can I find a ESP32-S3-WROOM-1U reference design?

Each of the 30 boards on this page is a real design using the ESP32-S3-WROOM-1U. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What pull-up resistor is used on the ESP32-S3-WROOM-1U EN pin?

The EN pin has a pull-up to 3.3V on 19 of 20 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 20 open source designs using the ESP32-S3-WROOM-1U.

How is the ESP32-S3-WROOM-1U 3V3 pin connected?

The 3V3 pin is tied to 3.3V on 19 of 20 designs. Counted from the KiCad layouts of 20 open source designs using the ESP32-S3-WROOM-1U.

How is the ESP32-S3-WROOM-1U IO35 pin connected?

The IO35 pin is left unconnected on 18 of 20 designs (a signal on 2). Counted from the KiCad layouts of 20 open source designs using the ESP32-S3-WROOM-1U.

What parts are used alongside the ESP32-S3-WROOM-1U?

The LD1117S33TR_SOT223, MAX98357A, ME6211C33M5 and TP4056-42-ESOP8 appear in the most repositories here.

Which microcontrollers do boards using the ESP32-S3-WROOM-1U use?

Most are built on ESP32 (30).

How big is a typical board using the ESP32-S3-WROOM-1U?

The median is 67.5 × 60 mm, and 47% are two-layer designs.

What is the most popular open source board using the ESP32-S3-WROOM-1U?

By GitHub stars, PCBA-KNOT by intechstudio, with 57 stars.

Can I simulate one of these boards using the ESP32-S3-WROOM-1U before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part