19 open source boards using the IR2104

Real designs built with the IR2104, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

19 boardsClear filters|Most starred

How designs wire the IR2104

Read from the KiCad layouts of 17 open source designs, one per repository: what each pin of the IR2104 connects to, and the resistors, capacitors and other passives placed on it.

  • The LO pin has a series resistor on 17 of 17 designs, most often 10 Ω (then 47 Ω).
  • The VS pin has a series capacitor on 17 of 17 designs, most often 1 µF (then 100 nF).
  • The HO pin has a series resistor on 17 of 17 designs, most often 10 Ω (then 47 Ω).
  • The VB pin has a series capacitor on 17 of 17 designs, most often 1 µF (then 10 µF).
VCCpin 1Connected to: 12V 82% · a signal 18%
  • Decoupling capacitor on 53% · 100 nF (8), 10 µF (2), 1 µF (1)
COMpin 4Connected to: GND 100%
LOpin 5Connected to: Signal 100%
  • Series resistor on 100% · 10 Ω (7), 47 Ω (3), 27 Ω (2)
VSpin 6Connected to: A connector 53%
  • Series capacitor on 100% · 1 µF (7), 100 nF (3), 10 µF (2)
  • Series resistor on 35% · 5 mΩ (2), 10 kΩ (2), 100 kΩ (1)
HOpin 7Connected to: Signal 100%
  • Series resistor on 100% · 10 Ω (7), 47 Ω (3), 27 Ω (2)
VBpin 8Connected to: Signal 100%
  • Series capacitor on 100% · 1 µF (7), 10 µF (2), 10 nF (2)

2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Charge Controller by jharvey, Dual h bridge by jayanta525, Placa buck by fadelrio and Brushless ESC by FordPrfkt.

The IR2104 in open source designs

The gallery holds 19 open source boards using the IR2104 from 17 GitHub repositories; a typical one measures about 88.4 × 66.3 mm and carries around 59 components.

79% are two-layer designs, the rest use four layers or more, and 47% carry an open source license.

The most starred is Charge Controller by jharvey.

Microcontrollers on boards using the IR2104

IR2104: common questions

Where can I find a IR2104 reference design?

Each of the 19 boards on this page is a real design using the IR2104. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What resistor goes on the IR2104 LO pin?

The LO pin has a series resistor on 17 of 17 designs, most often 10 Ω (then 47 Ω). Counted from the KiCad layouts of 17 open source designs using the IR2104.

How is the IR2104 VS pin connected?

The VS pin has a series capacitor on 17 of 17 designs, most often 1 µF (then 100 nF). Counted from the KiCad layouts of 17 open source designs using the IR2104.

What resistor goes on the IR2104 HO pin?

The HO pin has a series resistor on 17 of 17 designs, most often 10 Ω (then 47 Ω). Counted from the KiCad layouts of 17 open source designs using the IR2104.

What parts are used alongside the IR2104?

The AMS1117-3.3, TL431LP, AMS1117-5.0, Arduino_Nano_v3.x and CH340C appear in the most repositories here.

Which microcontrollers do boards using the IR2104 use?

Most are built on AVR/Arduino (5), STM32 (3), RP2040/RP2350 (2) and ESP32 (1).

How big is a typical board using the IR2104?

The median is 88.4 × 66.3 mm, and 79% are two-layer designs.

What is the most popular open source board using the IR2104?

By GitHub stars, Charge Controller by jharvey, with 24 stars.

Can I simulate one of these boards using the IR2104 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part