12 open source boards using the MAX-M8

Real designs built with the MAX-M8, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

12 boardsClear filters|Most starred

How designs wire the MAX-M8

Read from the KiCad layouts of 11 open source designs, one per repository: what each pin of the MAX-M8 connects to, and the resistors, capacitors and other passives placed on it.

  • The VCC_IO pin has a decoupling capacitor on 9 of 10 designs, most often 100 nF.
  • The VCC pin has a decoupling capacitor on 9 of 10 designs, most often 100 nF (then 10 nF).
  • The LNA_EN pin is left unconnected on 10 of 10 designs.
  • The VCC_RF pin has a series resistor on 8 of 10 designs, most often 10 Ω.
GNDpin 1, 10, 12Connected to: GND 100%
V_BCKPpin 6Connected to: Signal 70% · 3.3V 20%
  • Pull-up to 3.3V on 60% · 0 Ω (12)
  • Capacitor to GND on 30% · 100 nF (3), 220 nF (1)
VCC_IOpin 7Connected to: 3.3V 100%
  • Decoupling capacitor on 90% · 100 nF (3)
VCCpin 8Connected to: 3.3V 100%
  • Decoupling capacitor on 90% · 100 nF (3), 10 nF (1)
RESETpin 9Connected to: 5M40ZE64 60% · not connected 20%
  • Resistor to GND on 60% · 100 kΩ (6)
RF_INpin 11Connected to: A connector 90%
  • Inductor on 80%
LNA_ENpin 13Connected to: Not connected 100%
VCC_RFpin 14Connected to: Signal 80%
  • Series resistor on 80% · 10 Ω (8)
V_ANTpin 15Connected to: GND 60% · not connected 30%
SDApin 16Connected to: The microcontroller 20% · not connected 20%
  • Ferrite bead on 60%
SCLpin 17Connected to: The microcontroller 20% · not connected 20%
  • Ferrite bead on 60%

5 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Portapack havoc modified by jamesshao8, Portapack carnage by Acetolyne, DigitalTxRxRPi by BrandenburgTech and PortaPack H1 by Josephrp.

The MAX-M8 in open source designs

The gallery holds 12 open source boards using the MAX-M8 from 11 GitHub repositories; a typical one measures about 120 × 75 mm and carries around 108 components.

60% are two-layer designs, the rest use four layers or more, and 50% carry an open source license.

The most starred is Portapack havoc modified by jamesshao8.

Microcontrollers on boards using the MAX-M8

MAX-M8: common questions

Where can I find a MAX-M8 reference design?

Each of the 12 boards on this page is a real design using the MAX-M8. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What decoupling capacitors do designs use on the MAX-M8 VCC_IO pin?

The VCC_IO pin has a decoupling capacitor on 9 of 10 designs, most often 100 nF. Counted from the KiCad layouts of 11 open source designs using the MAX-M8.

What decoupling capacitors do designs use on the MAX-M8 VCC pin?

The VCC pin has a decoupling capacitor on 9 of 10 designs, most often 100 nF (then 10 nF). Counted from the KiCad layouts of 11 open source designs using the MAX-M8.

How is the MAX-M8 LNA_EN pin connected?

The LNA_EN pin is left unconnected on 10 of 10 designs. Counted from the KiCad layouts of 11 open source designs using the MAX-M8.

What parts are used alongside the MAX-M8?

The 5M40ZE64, 74HC1G04GW, AK4951EN, BQ24075RGT and CAT4004[_AB] appear in the most repositories here.

Which microcontrollers do boards using the MAX-M8 use?

Most are built on Microchip SAM (2) and STM32 (1).

How big is a typical board using the MAX-M8?

The median is 120 × 75 mm, and 60% are two-layer designs.

What is the most popular open source board using the MAX-M8?

By GitHub stars, Portapack havoc modified by jamesshao8, with 186 stars.

Can I simulate one of these boards using the MAX-M8 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part