19 open source boards using the 4001
Real designs built with the 4001, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
281D
DunningtonAudio
104 × 158 mm370 parts4LGPL-3.024Pong
PlummersSoftwareLLC
142.2 × 124.5 mm26 parts2LGPL-3.012Euclid Main Board
m0xpd
78 × 108 mm128 parts2LCC-BY-SA-4.07Cosmac toy v2
kanpapa
72 × 95 mm56 parts2LNo license41802-Mini-Super-Elf-Bus
dmadole
100 × 100 mm54 parts2LNo license21802-Mini-Pixie-Video
dmadole
100 × 100 mm49 parts2LGPL-3.021802-Mini-Compact-Flash
dmadole
100 × 100 mm36 parts2LNo license2DMH VCEG PCB 1 Mk1 1
DeMarco
148 × 175 mm241 parts2LCC0-1.011802-Mini-Front-Panel
dmadole
100 × 86.4 mm49 parts2LNo license11802-Mini-1854-Serial
dmadole
100 × 100 mm44 parts2LNo license1Modular sound synthesizer
zetapersei
163.1 × 114 mm97 parts2LGPL-3.001802-Mini-9918-Video
dmadole
100 × 100 mm73 parts2LNo license0Nol
0x007E
77.5 × 50.8 mm66 parts2LCC-BY-NC-4.001802-Mini-Expander-RTC
dmadole
100 × 100 mm65 parts2LNo license0AC30
linuxha
173 × 97.5 mm65 parts2LNo license0- schematic only · 13 parts
8x8 memory cell rtl
TIShoueb
13 partsNo license0 DMH VCEG PCB 1
DeMarco
148 × 175 mm239 parts2LCC0-1.01AVR/Arduino
VIA I/O Card
rjhelms
99.1 × 78.7 mm69 parts2LNo license2- schematic only · 175 parts
Building blocks
lennartquerter
175 parts2LCC-BY-NC-4.012
How designs wire the 4001
Read from the KiCad layouts of 16 open source designs, one per repository: what each pin of the 4001 connects to, and the resistors, capacitors and other passives placed on it.
- The - pins have a series resistor on 8 of 16 designs, most often 47 kΩ (then 10 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: Signal 75% · not connected 19% |
|
| -pin 2, 6, 9, 13 | Connected to: A connector 33% |
|
| +pin 3, 5, 10, 12 | Connected to: Signal 73% · not connected 27% |
|
| VSSpin 7 | Connected to: GND 88% | — |
| VDDpin 14 | Connected to: VCC 88% |
|
3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include 281D by DunningtonAudio, PongPCB by PlummersSoftwareLLC, Euclid Control Board by m0xpd and Cosmac toy v2 by kanpapa.
The 4001 in open source designs
The gallery holds 19 open source boards using the 4001 from 18 GitHub repositories; a typical one measures about 100 × 100 mm and carries around 65 components.
94% are two-layer designs, the rest use four layers or more, and 37% carry an open source license.
The most starred is 281D by DunningtonAudio.
Microcontrollers on boards using the 4001
What boards using the 4001 are built for
4001: common questions
Where can I find a 4001 reference design?
Each of the 19 boards on this page is a real design using the 4001. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the 4001 - pin?
The - pins have a series resistor on 8 of 16 designs, most often 47 kΩ (then 10 kΩ). Counted from the KiCad layouts of 16 open source designs using the 4001.
What parts are used alongside the 4001?
The 4013, 4011, 4023, 4049 and 4024 appear in the most repositories here.
Which microcontrollers do boards using the 4001 use?
Most are built on AVR/Arduino (1).
How big is a typical board using the 4001?
The median is 100 × 100 mm, and 94% are two-layer designs.
What is the most popular open source board using the 4001?
By GitHub stars, 281D by DunningtonAudio, with 24 stars.
Can I simulate one of these boards using the 4001 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.