14 open source boards using the 7406
Real designs built with the 7406, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Pi1541io
hackup
65 × 56 mm50 parts2LCC-BY-SA-4.0108Vic2020mainboard
danwerner21
357.8 × 124.5 mm127 parts2LNo license78C64 Pi1541-II Module
tebl
97.8 × 97.8 mm26 parts2LCERN-OHL-1.259C64 Pi1541-III Module
tebl
100 × 100 mm20 parts2LCERN-OHL-1.244C64-Pi1541-Module
tebl
65 × 56.5 mm18 parts2LNo license34We816
danwerner21
360.1 × 141.4 mm128 parts2LNo license32- schematic only · 97 parts
K-1013-floppy disk controller replica
eduardocasino
97 partsCustom license3 AVR/Arduino
Sbc 8088
miselin
243.8 × 243.8 mm206 parts4LCERN-OHL-P-2.02RP2040/RP2350
We816-mark2
danwerner21
360.1 × 141.4 mm128 parts2LNo license1EPROM Card
codesqueak
203.2 × 203.2 mm77 parts2LCERN-OHL-S-2.01CBM-II-Fastbus
sjgray
77.3 × 50 mm33 parts2LNo license0Lomax Thunder 186 Redux
RichCini
253.6 × 137.7 mm116 parts4LNo license1GIMIX DMA Floppy
roberto314
248.9 × 139.7 mm124 parts2LBSD-2-Clause1St225 20427
schlae
136.8 × 199.1 mm212 parts2LNo license38
How designs wire the 7406
Read from the KiCad layouts of 13 open source designs, one per repository: what each pin of the 7406 connects to, and the resistors, capacitors and other passives placed on it.
- Pin 2 has a pull-up to 5V on 10 of 13 designs, most often 1 kΩ (then 10 kΩ).
- Pin 4 has a pull-up to 5V on 9 of 13 designs, most often 1 kΩ (then 10 kΩ).
- The VCC pin has a decoupling capacitor on 9 of 13 designs, most often 100 nF (then 10 nF).
- Pin 12 is left unconnected on 9 of 13 designs (a signal on 4).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 2 | Connected to: A connector 77%, I2C LC 23% |
|
| Pin 4 | Connected to: A connector 77%, I2C LC 23% |
|
| Pin 6 | Connected to: A connector 38% · not connected 38% |
|
| GNDpin 7 | Connected to: GND 100% | — |
| Pin 8 | Connected to: A connector 38% · not connected 46% |
|
| Pin 10 | Connected to: Not connected 62% · a signal 38% | — |
| Pin 12 | Connected to: Not connected 69% · a signal 31% | — |
| VCCpin 14 | Connected to: 5V 100% |
|
6 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Pi1541io by hackup, Vic2020mainboard by danwerner21, C64 Pi1541-II Module by tebl and C64 Pi1541-III Module by tebl.
The 7406 in open source designs
The gallery holds 14 open source boards using the 7406 from 14 GitHub repositories; a typical one measures about 203.2 × 137.7 mm and carries around 107 components.
85% are two-layer designs, the rest use four layers or more, and 43% carry an open source license.
The most starred is Pi1541io by hackup.
Parts used alongside the 7406
Microcontrollers on boards using the 7406
What boards using the 7406 are built for
7406: common questions
Where can I find a 7406 reference design?
Each of the 14 boards on this page is a real design using the 7406. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the 7406 pin 2?
Pin 2 has a pull-up to 5V on 10 of 13 designs, most often 1 kΩ (then 10 kΩ). Counted from the KiCad layouts of 13 open source designs using the 7406.
What pull-up resistor is used on the 7406 pin 4?
Pin 4 has a pull-up to 5V on 9 of 13 designs, most often 1 kΩ (then 10 kΩ). Counted from the KiCad layouts of 13 open source designs using the 7406.
What decoupling capacitors do designs use on the 7406 VCC pin?
The VCC pin has a decoupling capacitor on 9 of 13 designs, most often 100 nF (then 10 nF). Counted from the KiCad layouts of 13 open source designs using the 7406.
What parts are used alongside the 7406?
The 74LS244, 74LS04, 74LS138, 74LS14 and 74LS245 appear in the most repositories here.
Which microcontrollers do boards using the 7406 use?
Most are built on AVR/Arduino (1) and RP2040/RP2350 (1).
How big is a typical board using the 7406?
The median is 203.2 × 137.7 mm, and 85% are two-layer designs.
What is the most popular open source board using the 7406?
By GitHub stars, Pi1541io by hackup, with 108 stars.
Can I simulate one of these boards using the 7406 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.