29 open source boards using the INA219AIDCNR
Real designs built with the INA219AIDCNR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
OpenJetECU
yuchao86
100.1 × 60.2 mm187 parts4LGPL-3.084ch-RF-FE
JohnnyGOX17
249.9 × 94.7 mm275 parts4LMIT5Hw udsp card
crsknr
60 × 30 mm211 parts6LGPL-3.02EEE3088F project group 59
Khahulesingo144
80 × 55 mm55 parts2LNo license1STM32
PC ExtensionBoard
caotiendattx
128.3 × 98.3 mm263 parts6LNo license0Hades
david-who
100.1 × 60.2 mm187 parts4LBSD-3-Clause0Raspberry Pi
Default
jackalkahwati
1500 × 290 mm180 parts2LNo license0ESP32
VibePCB-bench psu
PaulBichl
90 × 76 mm87 parts4LNo license0ESP32
Motion play main
moclei
88.2 × 38.5 mm84 parts4LNo license0Power subsystem
MTHSEK006
59.3 × 80.4 mm71 parts2LNo license0Micromouse-Lula and-Rejoice
LlamaLuLu
82 × 60 mm65 parts2LNo license0EEE3088F-Micromouse power module-
May-engineer
73.7 × 53.9 mm65 parts2LNo license0EEE3088F MM Power Project
KLPJOA002
77.3 × 58.5 mm59 parts2LNo license0ESP32
Chipsat v1
noellayang
45.5 × 46 mm59 parts2LMIT0EEE3088F 2025
TTembe
80 × 60 mm57 parts2LNo license0ESP32
Jchc1-hardware
GutFarms
100 × 70 mm15 parts4LNo license0- schematic only · 195 partsSTM32
HadesFCS
avajones081196
195 partsNo license0 Raspberry Pi
Rev a cleanup
jackalkahwati
200 × 175 mm179 parts4LNo license0STM32
HadesNT
david-who
80 × 50 mm94 parts4LBSD-3-Clause0ESP32
RX 50MHz SDR
ne9n
150 × 85 mm44 parts2LNo license0Joab Schematics
KLPJOA002
62.5 × 65.3 mm39 parts2LNo license0BenchRail-INA USB-C Dual-Rail Precision Monitor
draarivpatel-ui
62 × 42 mm18 parts2LMIT0Raspberry Pi
Rev a routed
jackalkahwati
200 × 175 mm179 parts4LNo license0- schematic only · 19 parts
Alex Schematics
KLPJOA002
19 parts2LNo license0 Raspberry Pi
Dut power rev a
jackalkahwati
160 × 100 mm145 parts4LNo license0USB Hub
Phil-CIA
100 × 50 mm76 parts4LNo license0USB Hub Next Iter
Phil-CIA
100 × 50 mm76 parts4LNo license0AVR/Arduino
Boson Breakout
gregdavill
45 × 78 mm35 parts4LNo license178AVR/Arduino
Tau2 Breakout
gregdavill
45 × 78 mm32 parts4LNo license178
How designs wire the INA219AIDCNR
Read from the KiCad layouts of 19 open source designs, one per repository: what each pin of the INA219AIDCNR connects to, and the resistors, capacitors and other passives placed on it.
- The IN+ pin has a series resistor on 15 of 19 designs, most often 10 mΩ (then 4.7 kΩ).
- The IN- pin has a series resistor on 12 of 19 designs, most often 10 mΩ (then 10 kΩ).
- The VS pin has a decoupling capacitor on 11 of 19 designs, most often 100 nF (then 10 µF).
- The A0 pin is tied to GND on 12 of 18 designs (3.3V on 2, a signal on 4).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| IN+pin 1 | Connected to: A connector 21% |
|
| IN-pin 2 | Connected to: Signal 74% · GND 16% |
|
| GNDpin 3 | Connected to: GND 79% · a signal 21% | — |
| VSpin 4 | Connected to: 3.3V 58% · a signal 42% |
|
| SCLpin 5 | Connected to: A connector 42%, the microcontroller 32%, INA219AIDCNR 21% |
|
| SDApin 6 | Connected to: A connector 37%, the microcontroller 32%, INA219AIDCNR 21% |
|
| A0pin 7 | Connected to: GND 67% · a signal 22% | — |
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Boson Breakout by gregdavill, OpenJetECU by yuchao86, 4ch-RF-FE by JohnnyGOX17 and Hw udsp card by crsknr.
The INA219AIDCNR in open source designs
The gallery holds 29 open source boards using the INA219AIDCNR from 21 GitHub repositories; a typical one measures about 88.2 × 60.2 mm and carries around 76 components.
57% use four copper layers or more, and 24% carry an open source license.
The most starred is Boson Breakout by gregdavill.
Parts used alongside the INA219AIDCNR
Microcontrollers on boards using the INA219AIDCNR
What boards using the INA219AIDCNR are built for
INA219AIDCNR: common questions
Where can I find a INA219AIDCNR reference design?
Each of the 29 boards on this page is a real design using the INA219AIDCNR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the INA219AIDCNR IN+ pin?
The IN+ pin has a series resistor on 15 of 19 designs, most often 10 mΩ (then 4.7 kΩ). Counted from the KiCad layouts of 19 open source designs using the INA219AIDCNR.
What resistor goes on the INA219AIDCNR IN- pin?
The IN- pin has a series resistor on 12 of 19 designs, most often 10 mΩ (then 10 kΩ). Counted from the KiCad layouts of 19 open source designs using the INA219AIDCNR.
What decoupling capacitors do designs use on the INA219AIDCNR VS pin?
The VS pin has a decoupling capacitor on 11 of 19 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 19 open source designs using the INA219AIDCNR.
What parts are used alongside the INA219AIDCNR?
The USBLC6-2SC6, AMS1117-3.3, HUSB237-AA001-DN06R, 24CW1280T-I/OT and AP2112K-3.3TRG1 appear in the most repositories here.
Which microcontrollers do boards using the INA219AIDCNR use?
Most are built on ESP32 (5), Raspberry Pi (4), STM32 (3) and AVR/Arduino (2).
How big is a typical board using the INA219AIDCNR?
The median is 88.2 × 60.2 mm, and 43% are two-layer designs.
What is the most popular open source board using the INA219AIDCNR?
By GitHub stars, Boson Breakout by gregdavill, with 178 stars.
Can I simulate one of these boards using the INA219AIDCNR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.