27 open source boards using the LM2904
Real designs built with the LM2904, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
DAC ADC PWM IO
DanielMartensson
100 × 100 mm266 parts4LMIT180NXP
Precharge
michaelruppe
133 × 98 mm110 parts2LMIT56CTA control board
PySpice-org
252 × 152 mm614 parts4LNo license9NXP
Precharge
LSUTigerRacing
133 × 98 mm113 parts2LNo license7STM32
BMW-K1200LT-ABS-Conversion
OstapFerensovych
61.4 × 49 mm63 parts2LMIT7ESP32
Mainboard
Synthron
160 × 100 mm206 parts4LNo license3DelSol Mixer
dzavalishin
254 × 54 mm121 parts2LNo license3Lunchbox adapter
Spritkopf
67.6 × 89.2 mm83 parts2LGPL-3.02AVR/Arduino
Soylent
kulp
17.8 × 22.9 mm24 parts2LNo license1STM32
Xtec uc ip main
ADFTech
190 × 109 mm538 parts2LNo license0STM32
RC Charger
aokblast
200 × 100 mm296 parts4LNo license0Analog audio visualizer
alimleahat
130 × 100 mm65 parts2LNo license0Projects
hasanyucelcogal
55.9 × 37.5 mm32 parts2LNo license0STM32
DAC ADC PWM IO BACK UP
DanielMartensson
100 × 100 mm266 parts4LMIT180Microchip SAM
Pi TX 35W PA V2
M0LTE
100 × 100 mm161 parts4LNo license15Dacha Talker
dzavalishin
71 × 140 mm110 parts2LNo license3Awg
bradencamp
78.7 × 72.6 mm74 parts2LNo license1Mod Temp Driver
Gonzalogontad
70 × 100 mm71 parts2LNo license0ESP32
Mainboard 767
Synthron
160 × 100 mm195 parts4LNo license3BPSD-2025
LSUTigerRacing
68.5 × 43 mm50 parts2LNo license7STM32
Power SMPS
Synthron
160 × 100 mm112 parts2LNo license3Poncho Procesador de Audio
brengi
85.9 × 137 mm83 parts2LNo license7RealQuadcellAmp
UChicago-Space-Program
75.6 × 76.1 mm48 parts2LNo license1STM32
Electronic Load
Synthron
160 × 100 mm102 parts4LNo license3STM32
Current sensor filter
Synthron
160 × 100 mm91 parts4LNo license3STM32
Diode Tester
Synthron
160 × 100 mm85 parts2LNo license3DelSol Preamp
dzavalishin
110.5 × 38.1 mm75 parts2LNo license3
How designs wire the LM2904
Read from the KiCad layouts of 18 open source designs, one per repository: what each pin of the LM2904 connects to, and the resistors, capacitors and other passives placed on it.
- The - pins have a series resistor on 16 of 18 designs, most often 10 kΩ (then 100 kΩ).
- The + pins have a series resistor on 13 of 18 designs, most often 10 kΩ (then 50 kΩ).
- Pin 7 has a series resistor on 11 of 17 designs, most often 10 kΩ (then 100 kΩ).
- The V- pin is tied to GND on 13 of 18 designs (-12V on 3, a signal on 2).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| -pin 1, 2, 6 | Connected to: Signal 91% |
|
| +pin 3, 5 | Connected to: Signal 86% |
|
| V-pin 4 | Connected to: GND 72% · -12V 17% | — |
| Pin 7 | Connected to: Signal 94% |
|
| V+pin 8 | Connected to: 12V 88% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include DAC ADC PWM IO by DanielMartensson, Precharge by michaelruppe, Pi TX 35W PA V2 by M0LTE and CTA control board by PySpice-org.
The LM2904 in open source designs
The gallery holds 27 open source boards using the LM2904 from 18 GitHub repositories; a typical one measures about 110.5 × 100 mm and carries around 102 components.
67% are two-layer designs, the rest use four layers or more, and 19% carry an open source license.
The most starred is DAC ADC PWM IO by DanielMartensson.
Parts used alongside the LM2904
Microcontrollers on boards using the LM2904
What boards using the LM2904 are built for
LM2904: common questions
Where can I find a LM2904 reference design?
Each of the 27 boards on this page is a real design using the LM2904. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the LM2904 - pin?
The - pins have a series resistor on 16 of 18 designs, most often 10 kΩ (then 100 kΩ). Counted from the KiCad layouts of 18 open source designs using the LM2904.
What resistor goes on the LM2904 + pin?
The + pins have a series resistor on 13 of 18 designs, most often 10 kΩ (then 50 kΩ). Counted from the KiCad layouts of 18 open source designs using the LM2904.
What resistor goes on the LM2904 pin 7?
Pin 7 has a series resistor on 11 of 17 designs, most often 10 kΩ (then 100 kΩ). Counted from the KiCad layouts of 18 open source designs using the LM2904.
What parts are used alongside the LM2904?
The LM2902, LM1117-5.0, 4N35, LM331 and LM393 appear in the most repositories here.
Which microcontrollers do boards using the LM2904 use?
Most are built on STM32 (9), ESP32 (2), NXP (2) and AVR/Arduino (1).
How big is a typical board using the LM2904?
The median is 110.5 × 100 mm, and 67% are two-layer designs.
What is the most popular open source board using the LM2904?
By GitHub stars, DAC ADC PWM IO by DanielMartensson, with 180 stars.
Can I simulate one of these boards using the LM2904 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.