68 open source boards using the LM741
Real designs built with the LM741, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Microdigital - TK 2000
clemarfolly
236.8 × 169.8 mm195 parts2LNo license17Synbal
Bad-Dog-Designs
71 × 108 mm105 parts2LGPL-2.014Main
ceteras
299.2 × 180 mm352 parts2LMIT11Digital-Stethoscope
darknight2163
113.1 × 41.3 mm30 parts2LNo license9AVR/Arduino
Dac shield
visgence
68.6 × 53.3 mm31 parts2LNo license5EuroClack Formant LFO panel
clacktronics
70.8 × 128.5 mm101 parts2LNo license4Peoples permacomputer
genossen
208.3 × 146.1 mm121 parts2LCustom license2M-NET-Thermostat
gajdi88
55.9 × 64.8 mm33 parts2LGPL-3.02AVR/Arduino
Voltage amplifier
Sussex-Neuroscience
111.5 × 85.1 mm19 parts2LGPL-3.02AVR/Arduino
SignalGenerator
ukmaker
99.8 × 100 mm115 parts2LNo license1Elektronica2-Labo-Opstelling
TiebeDeclercq
100 × 100 mm82 parts2LMIT1S2l board
jevans3142
91.4 × 99.1 mm61 parts2LNo license12026-2027
Sheffield-Sound-Systems
38 × 46.8 mm31 parts2LMIT1FUNCTION GENRATOR
sarthak8926
200 × 100 mm22 parts2LMIT1- schematic only · 74 parts
Jensx1000
icnagy
74 partsCERN-OHL-S-2.01 PCB HORNO
Bojtronic
226.2 × 263.7 mm249 parts2LNo license0Analogulator
Tamizhanban212
110 × 112 mm100 parts2LNo license0Motor Health Monitoring 8051
YUKESH0620
135.2 × 73.1 mm99 parts4LMIT0Alimentatore
CarloMara
117.6 × 97.8 mm83 parts2LNo license0STM32
STM32F103 iot
R-Mutura
50 × 67.5 mm82 parts2LNo license0ALU 2b
ChetanMandloi
111.6 × 74.9 mm79 parts2LGPL-3.00Red-Crab
aitesam961
90.8 × 45.5 mm77 parts4LGPL-3.00Closed Loop DC Motor Speed Control
Ammar-Bin-Amir
175.8 × 66.1 mm59 parts2LNo license0Continous servo
georgesleen
95.3 × 56.5 mm52 parts4LGPL-3.00Analog Project PLL
Pranay-Patil2006
95 × 97.5 mm35 parts2LNo license0Board
awkwardbunny
96.8 × 80.9 mm30 parts2LGPL-3.00PID-position
azzamjhd
50 × 50 mm29 parts2LNo license0FiltruTreceBanda
AndreiStefanov
130 × 46.5 mm29 parts2LNo license0PCB-Design
ahabiqbal08
85.9 × 59.5 mm28 parts2LNo license0Sinewave generator circuit with
Mohamed-U3
66.4 × 66.6 mm20 parts2LMIT0Operational-Amplifier-Test-Board
MateoHadzimustafic
49 × 48.6 mm14 parts2LApache-2.00Dominik power supply
kwn
48 × 38 mm13 parts2LNo license0Open Loop DC Motor Speed Control
Ammar-Bin-Amir
38.1 × 22.9 mm12 parts2LNo license0Active-Low-Pass-Filter
Hawk453
80 × 45 mm10 parts2LGPL-3.00Inverting-Op-Amp
Rohit04121998
86.4 × 50.6 mm8 parts2LMIT0- schematic only · 3 parts
Analog-Waveform-Generator
FluxCapacitor37
3 partsNo license0
How designs wire the LM741
Read from the KiCad layouts of 55 open source designs, one per repository: what each pin of the LM741 connects to, and the resistors, capacitors and other passives placed on it.
- The NULL pins is left unconnected on 93% of them (a signal on 7).
- Pin 6 has a series resistor on 38 of 55 designs, most often 10 kΩ (then 100 kΩ).
- The - pin has a series resistor on 33 of 55 designs, most often 10 kΩ (then 1 kΩ).
- The + pin has a series resistor on 27 of 55 designs, most often 10 kΩ (then 100 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| NULLpin 1, 5 | Connected to: Not connected 93% | — |
| -pin 2 | Connected to: Signal 89% |
|
| +pin 3 | Connected to: Signal 84% · GND 16% |
|
| Pin 6 | Connected to: A connector 24% |
|
| V+pin 7 | Connected to: 12V 73% · a signal 22% | — |
| NCpin 8 | Connected to: Not connected 96% | — |
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include ISA65816 by robfinch, Microdigital - TK 2000 by clemarfolly, ADSR by telec16 and Synbal by Bad-Dog-Designs.
The LM741 in open source designs
The gallery holds 68 open source boards using the LM741 from 58 GitHub repositories; a typical one measures about 85.9 × 67.5 mm and carries around 33 components.
92% are two-layer designs, the rest use four layers or more, and 41% carry an open source license.
The most starred is ISA65816a by robfinch.
Parts used alongside the LM741
Microcontrollers on boards using the LM741
What boards using the LM741 are built for
LM741: common questions
Where can I find a LM741 reference design?
Each of the 68 boards on this page is a real design using the LM741. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the LM741 NULL pin connected?
The NULL pins is left unconnected on 93% of them (a signal on 7). Counted from the KiCad layouts of 55 open source designs using the LM741.
What resistor goes on the LM741 pin 6?
Pin 6 has a series resistor on 38 of 55 designs, most often 10 kΩ (then 100 kΩ). Counted from the KiCad layouts of 55 open source designs using the LM741.
What resistor goes on the LM741 - pin?
The - pin has a series resistor on 33 of 55 designs, most often 10 kΩ (then 1 kΩ). Counted from the KiCad layouts of 55 open source designs using the LM741.
What parts are used alongside the LM741?
The LM324, 74LS04, 74LS08, 74LS11 and 74LS138 appear in the most repositories here.
Which microcontrollers do boards using the LM741 use?
Most are built on AVR/Arduino (5), STM32 (2) and ESP32 (1).
How big is a typical board using the LM741?
The median is 85.9 × 67.5 mm, and 92% are two-layer designs.
What is the most popular open source board using the LM741?
By GitHub stars, ISA65816a by robfinch, with 78 stars.
Can I simulate one of these boards using the LM741 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.