33 open source boards using the SN74LVC2G17DBVR
Real designs built with the SN74LVC2G17DBVR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
FPGA
Ossc
marqs85
124.6 × 68.8 mm259 parts4LNo license162FPGA
RFToolSDR
daveshah1
98 × 100 mm290 parts4LMIT131PXU
Andr-Zero
198 × 64.5 mm119 parts4LCERN-OHL-S-2.0104Microchip SAM
WiFi-Gate-Control-Board
mikelawrence
139.7 × 158.8 mm252 parts4LNo license3STM32
Hub
Bruhdows
148 × 78 mm309 parts4LNo license1Channel Monitor C1
AnishLanka
180 × 145 mm137 parts2LNo license1Arena 12-12 v8 ni
floesche
228.6 × 228.6 mm575 parts6LCC-BY-4.00Qds cv
cnpem-emi
220 × 160 mm362 parts4LNo license0FE UFPR 4 0
josearistidesbail
159.6 × 130 mm313 parts4LNo license0Av board cb
bryfur
100 × 100 mm300 parts4LNo license0ESP32
Robot
jgraulle
100 × 100 mm183 parts2LNo license0FPGA
Amiga scandoubler v030wip
110-kenichi
95 × 95 mm139 parts4LNo license0GanFET-Buck-Converter
suryathanush
52.2 × 88.5 mm68 parts4LNo license0Assembly source
zcrawling
65 × 56 mm65 parts4LNo license0NXP
Arena 12-12 Teensy Modular LED Display
floesche
228.6 × 228.6 mm441 parts6LCC-BY-4.00Av board ca
bryfur
130 × 100 mm276 parts4LNo license0FPGA
Amiga scandoubler analog
110-kenichi
95 × 95 mm135 parts4LNo license0First route
zcrawling
65 × 56 mm65 parts4LNo license0RP2040/RP2350
Channel ADC Interface RevC
AnishLanka
125 × 85 mm69 parts2LNo license1FPGA
Amiga scandoubler distribution
110-kenichi
95 × 95 mm135 parts4LNo license0Prelayout b2
zcrawling
65 × 56 mm65 parts4LNo license0Av board b
bryfur
94.6 × 69.4 mm230 parts4LNo license0FPGA
Amiga scandoubler placement
110-kenichi
95 × 95 mm135 parts4LNo license0Rbphat
zcrawling
65 × 56 mm65 parts4LNo license0ArmEncoderBoard
01binary
34 × 34 mm29 parts2LNo license20FPGA
Amiga scandoubler pll top
110-kenichi
95 × 95 mm135 parts4LNo license0Seeded labelled
zcrawling
65 × 56 mm65 parts4LNo license0FPGA
Amiga scandoubler refined
110-kenichi
95 × 95 mm135 parts4LNo license0FPGA
Amiga scandoubler rgb out
110-kenichi
95 × 95 mm135 parts4LNo license0FPGA
Amiga scandoubler routing
110-kenichi
95 × 95 mm135 parts4LNo license0FPGA
Amiga scandoubler sync in
110-kenichi
95 × 95 mm135 parts4LNo license0FPGA
Amiga scandoubler sync out
110-kenichi
95 × 95 mm135 parts4LNo license0FPGA
Amiga scandoubler u2rot
110-kenichi
95 × 95 mm135 parts4LNo license0
How designs wire the SN74LVC2G17DBVR
Read from the KiCad layouts of 15 open source designs, one per repository: what each pin of the SN74LVC2G17DBVR connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 14 of 15 designs, most often 100 nF (then 2.2 µF).
- The 1A pin has a series resistor on 8 of 15 designs, most often 33 Ω (then 1 kΩ).
- The 2A pin has a series resistor on 7 of 15 designs, most often 1 kΩ (then 10 kΩ).
- The 1Y pin has a series resistor on 6 of 15 designs, most often 0 Ω (then 33 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| 1Apin 1 | Connected to: A connector 33% |
|
| GNDpin 2 | Connected to: GND 93% | — |
| 2Apin 3 | Connected to: A connector 20% |
|
| VCCpin 5 | Connected to: 3.3V 73% · a signal 27% |
|
| 1Ypin 6 | Connected to: The microcontroller 20% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Ossc pcb by marqs85, RFToolSDR by daveshah1, PXU by Andr-Zero and ArmEncoderBoard by 01binary.
The SN74LVC2G17DBVR in open source designs
The gallery holds 33 open source boards using the SN74LVC2G17DBVR from 15 GitHub repositories; a typical one measures about 95 × 95 mm and carries around 135 components.
88% use four copper layers or more, and 12% carry an open source license.
The most starred is Ossc pcb by marqs85.
Parts used alongside the SN74LVC2G17DBVR
Microcontrollers on boards using the SN74LVC2G17DBVR
What boards using the SN74LVC2G17DBVR are built for
SN74LVC2G17DBVR: common questions
Where can I find a SN74LVC2G17DBVR reference design?
Each of the 33 boards on this page is a real design using the SN74LVC2G17DBVR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the SN74LVC2G17DBVR VCC pin?
The VCC pin has a decoupling capacitor on 14 of 15 designs, most often 100 nF (then 2.2 µF). Counted from the KiCad layouts of 15 open source designs using the SN74LVC2G17DBVR.
What resistor goes on the SN74LVC2G17DBVR 1A pin?
The 1A pin has a series resistor on 8 of 15 designs, most often 33 Ω (then 1 kΩ). Counted from the KiCad layouts of 15 open source designs using the SN74LVC2G17DBVR.
What resistor goes on the SN74LVC2G17DBVR 2A pin?
The 2A pin has a series resistor on 7 of 15 designs, most often 1 kΩ (then 10 kΩ). Counted from the KiCad layouts of 15 open source designs using the SN74LVC2G17DBVR.
What parts are used alongside the SN74LVC2G17DBVR?
The SN74LVC1G17DBVR, AP2112K-3.3TRG1, SN74LVC1G04DBVR, SN74LVC1G08DBVR and SN74LVC1G11DBVR appear in the most repositories here.
Which microcontrollers do boards using the SN74LVC2G17DBVR use?
Most are built on FPGA (13), ESP32 (1), NXP (1) and RP2040/RP2350 (1).
How big is a typical board using the SN74LVC2G17DBVR?
The median is 95 × 95 mm, and 12% are two-layer designs.
What is the most popular open source board using the SN74LVC2G17DBVR?
By GitHub stars, Ossc pcb by marqs85, with 162 stars.
Can I simulate one of these boards using the SN74LVC2G17DBVR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.