18 open source boards using the 4040
Real designs built with the 4040, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Klangorium
hexagon5un
200 × 100 mm152 parts2LNo license65AVI1861
dmadole
29.9 × 17.2 mm9 parts2LGPL-2.015Zf vga
tangent3D
143 × 85 mm52 parts2LMIT10FreeDSP-CLASSIC-SMD-A
freeDSP
70.4 × 84.4 mm89 parts2LNo license7AVR/Arduino
Automata Generator Standard
Sirawit7205
246.4 × 127 mm121 parts2LNo license2EPROM-Programmer
codesqueak
140 × 100 mm66 parts2LCERN-OHL-S-2.01Binary adder
SwiftDust
98 × 51 mm34 parts2LNo license1MagCam
miki407
140 × 150 mm572 parts2LGPL-3.00Enhanced-EPROM-Programmer
codesqueak
145 × 130 mm74 parts2LCERN-OHL-S-2.00NLP VGA
cherry-takuan
117.5 × 99.7 mm66 parts2LNo license0ESP32
Pokepico hardware MFT2019
chip-da-tunetaro
90 × 60 mm54 parts2LNo license0BinaryCounter
Wjchou2
63.5 × 71.3 mm35 parts2LNo license0AVR/Arduino
P2000t cartridge reader
ifilot
68.6 × 53.3 mm3 parts2LGPL-3.00- schematic only · 42 parts
COSMAC controller
quantalume
42 partsNo license0 - schematic only · 25 parts
Rotation speed detector
Shrikrishna26
25 partsNo license0 DS7B-3
RWeick
154 × 46.5 mm16 parts2LGPL-3.05RS 232
cherry-takuan
99.7 × 99.7 mm55 parts2LCC-BY-SA-4.045IO board
cherry-takuan
99.7 × 99.7 mm36 parts2LCC-BY-SA-4.045
How designs wire the 4040
Read from the KiCad layouts of 15 open source designs, one per repository: what each pin of the 4040 connects to, and the resistors, capacitors and other passives placed on it.
- The RESET pin has a resistor to GND on 6 of 15 designs, most often 10 kΩ (then 1 MΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VSSpin 8 | Connected to: GND 100% | — |
| RESETpin 11 | Connected to: A connector 20% · GND 20% |
|
| VDDpin 16 | Connected to: VCC 87% |
|
13 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Klangorium by hexagon5un, IO board by cherry-takuan, AVI1861 by dmadole and Zf vga by tangent3D.
The 4040 in open source designs
The gallery holds 18 open source boards using the 4040 from 17 GitHub repositories; a typical one measures about 108.6 × 92.3 mm and carries around 53 components.
100% are two-layer designs, the rest use four layers or more, and 50% carry an open source license.
The most starred is Klangorium by hexagon5un.
Microcontrollers on boards using the 4040
What boards using the 4040 are built for
4040: common questions
Where can I find a 4040 reference design?
Each of the 18 boards on this page is a real design using the 4040. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the 4040 RESET pin?
The RESET pin has a resistor to GND on 6 of 15 designs, most often 10 kΩ (then 1 MΩ). Counted from the KiCad layouts of 15 open source designs using the 4040.
What parts are used alongside the 4040?
The 74HC04, 74HC165, 74HC74, 4049 and 74HC00 appear in the most repositories here.
Which microcontrollers do boards using the 4040 use?
Most are built on AVR/Arduino (2) and ESP32 (1).
How big is a typical board using the 4040?
The median is 108.6 × 92.3 mm, and 100% are two-layer designs.
What is the most popular open source board using the 4040?
By GitHub stars, Klangorium by hexagon5un, with 65 stars.
Can I simulate one of these boards using the 4040 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.