35 open source boards using the ATTINY85-20SU

Real designs built with the ATTINY85-20SU, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

35 boardsClear filters|Most starred

How designs wire the ATTINY85-20SU

Read from the KiCad layouts of 31 open source designs, one per repository: what each pin of the ATTINY85-20SU connects to, and the resistors, capacitors and other passives placed on it.

  • The VCC pin has a decoupling capacitor on 21 of 31 designs, most often 100 nF (then 4.7 µF).
  • The PB1 pin has a series resistor on 14 of 31 designs, most often 330 Ω (then 1 kΩ).
  • The RESET/PB5 pin has a pull-up to 5V on 13 of 31 designs, most often 10 kΩ (then 1 kΩ).
RESET/PB5pin 1Connected to: A connector 52%
  • Pull-up to 5V on 42% · 10 kΩ (8), 1 kΩ (1), 22 kΩ (1)
XTAL1/PB3pin 2Connected to: Signal 81% · not connected 16%
  • Series resistor on 35% · 22 kΩ (6), 330 Ω (4), 68 Ω (2)
XTAL2/PB4pin 3Connected to: Signal 74% · not connected 23%
  • Series resistor on 35% · 330 Ω (3), 68 Ω (2), 22 kΩ (2)
GNDpin 4Connected to: GND 97%
AREF/PB0pin 5Connected to: A connector 55%
  • Series resistor on 35% · 220 Ω (3), 330 Ω (3), 10 kΩ (2)
PB1pin 6Connected to: A connector 52%
  • Series resistor on 45% · 330 Ω (5), 1 kΩ (3), 10 kΩ (2)
VCCpin 8Connected to: 5V 97%
  • Decoupling capacitor on 68% · 100 nF (18), 4.7 µF (4), 100 µF (1)

1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include SuperPower-RPi-KiCAD by SensorsIot, Battery by iam4722202468, Snopf by snopf and C64 Saver addon board by bwack.

The ATTINY85-20SU in open source designs

The gallery holds 35 open source boards using the ATTINY85-20SU from 32 GitHub repositories; a typical one measures about 49.9 × 45.3 mm and carries around 21 components.

91% are two-layer designs, the rest use four layers or more, and 49% carry an open source license.

The most starred is SuperPower-RPi-KiCAD by SensorsIot.

Parts used alongside the ATTINY85-20SU

Microcontrollers on boards using the ATTINY85-20SU

ATTINY85-20SU: common questions

Where can I find a ATTINY85-20SU reference design?

Each of the 35 boards on this page is a real design using the ATTINY85-20SU. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What decoupling capacitors do designs use on the ATTINY85-20SU VCC pin?

The VCC pin has a decoupling capacitor on 21 of 31 designs, most often 100 nF (then 4.7 µF). Counted from the KiCad layouts of 31 open source designs using the ATTINY85-20SU.

What resistor goes on the ATTINY85-20SU PB1 pin?

The PB1 pin has a series resistor on 14 of 31 designs, most often 330 Ω (then 1 kΩ). Counted from the KiCad layouts of 31 open source designs using the ATTINY85-20SU.

What pull-up resistor is used on the ATTINY85-20SU RESET/PB5 pin?

The RESET/PB5 pin has a pull-up to 5V on 13 of 31 designs, most often 10 kΩ (then 1 kΩ). Counted from the KiCad layouts of 31 open source designs using the ATTINY85-20SU.

What parts are used alongside the ATTINY85-20SU?

The AP2112K-3.3TRG1, 7805, MTCH101T-I_OT and PAM8002 appear in the most repositories here.

Which microcontrollers do boards using the ATTINY85-20SU use?

Most are built on AVR/Arduino (34) and STM32 (1).

How big is a typical board using the ATTINY85-20SU?

The median is 49.9 × 45.3 mm, and 91% are two-layer designs.

What is the most popular open source board using the ATTINY85-20SU?

By GitHub stars, SuperPower-RPi-KiCAD by SensorsIot, with 601 stars.

Can I simulate one of these boards using the ATTINY85-20SU before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part