39 open source boards using the ICL7660

Real designs built with the ICL7660, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

39 boardsClear filters|Most starred

How designs wire the ICL7660

Read from the KiCad layouts of 31 open source designs, one per repository: what each pin of the ICL7660 connects to, and the resistors, capacitors and other passives placed on it.

  • The CAP+ pin has a series capacitor on 30 of 31 designs, most often 10 µF (then 220 nF).
  • The CAP- pin has a series capacitor on 27 of 31 designs, most often 10 µF.
  • The OSC pin is left unconnected on 29 of 31 designs (5V on 2).
  • The LV pin is left unconnected on 28 of 31 designs (GND on 3).
NCpin 1Connected to: Not connected 94%
CAP+pin 2Connected to: Signal 100%
  • Series capacitor on 97% · 10 µF (27), 220 nF (1), 1 µF (1)
GNDpin 3Connected to: GND 90%
CAP-pin 4Connected to: Signal 87%
  • Series capacitor on 87% · 10 µF (26)
VOUTpin 5Connected to: -5V 48% · a signal 39%
  • Decoupling capacitor on 65% · 10 µF (18), 100 nF (7), 1 µF (2)
LVpin 6Connected to: Not connected 90%
OSCpin 7Connected to: Not connected 94%
V+pin 8Connected to: 5V 87%

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Actionneur piezo by claynicholson, Osillyscope-2layer by tvlad1234, Leako by barbeque and I8080-sbc by quasiengineer.

The ICL7660 in open source designs

The gallery holds 39 open source boards using the ICL7660 from 31 GitHub repositories; a typical one measures about 90 × 68.6 mm and carries around 59 components.

87% are two-layer designs, the rest use four layers or more, and 49% carry an open source license.

The most starred is Actionneur piezo by claynicholson.

Microcontrollers on boards using the ICL7660

ICL7660: common questions

Where can I find a ICL7660 reference design?

Each of the 39 boards on this page is a real design using the ICL7660. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the ICL7660 CAP+ pin connected?

The CAP+ pin has a series capacitor on 30 of 31 designs, most often 10 µF (then 220 nF). Counted from the KiCad layouts of 31 open source designs using the ICL7660.

How is the ICL7660 CAP- pin connected?

The CAP- pin has a series capacitor on 27 of 31 designs, most often 10 µF. Counted from the KiCad layouts of 31 open source designs using the ICL7660.

How is the ICL7660 OSC pin connected?

The OSC pin is left unconnected on 29 of 31 designs (5V on 2). Counted from the KiCad layouts of 31 open source designs using the ICL7660.

What parts are used alongside the ICL7660?

The 78L05, AMS1117-3.3, LM358N, TL072 and CH340C appear in the most repositories here.

Which microcontrollers do boards using the ICL7660 use?

Most are built on STM32 (6), AVR/Arduino (3), ESP32 (2) and RISC-V (2).

How big is a typical board using the ICL7660?

The median is 90 × 68.6 mm, and 87% are two-layer designs.

What is the most popular open source board using the ICL7660?

By GitHub stars, Actionneur piezo by claynicholson, with 102 stars.

Can I simulate one of these boards using the ICL7660 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part