10 open source boards using the LM5050-1

Real designs built with the LM5050-1, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

10 boardsClear filters|Most starred

How designs wire the LM5050-1

Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the LM5050-1 connects to, and the resistors, capacitors and other passives placed on it.

  • The VS pin has a capacitor to GND on 8 of 9 designs, most often 100 nF.
  • The VS pin has a pull-up to 5V on 7 of 9 designs, most often 100 Ω (then 1.5 kΩ).
  • The IN pin has a capacitor to GND on 7 of 9 designs, most often 22 µF (then 47 µF).
  • The OUT pin is tied to 5V on 7 of 9 designs (a signal on 2).
VSpin 1Connected to: Signal 100%
  • Capacitor to GND on 89% · 100 nF (7)
  • Pull-up to 5V on 78% · 100 Ω (6), 1.5 kΩ (1)
GNDpin 2Connected to: GND 89%
INpin 4Connected to: AP63205 44% · 5V 22%
  • Capacitor to GND on 78% · 22 µF (8), 47 µF (3), 100 nF (3)
  • Inductor on 44% · 6.8 µH (4)
OUTpin 6Connected to: 5V 78% · a signal 22%

2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Elec RPI Robot HAT by pollen-robotics, Mainboard by mincrmatt12, Grippette - USB hub and Dynamixel device by pollen-robotics and Flashlight power input dev by ahmadtak-3212.

The LM5050-1 in open source designs

The gallery holds 10 open source boards using the LM5050-1 from 10 GitHub repositories; a typical one measures about 65 × 30.9 mm and carries around 118 components.

89% use four copper layers or more, and 50% carry an open source license.

The most starred is Elec RPI Robot HAT by pollen-robotics.

Microcontrollers on boards using the LM5050-1

LM5050-1: common questions

Where can I find a LM5050-1 reference design?

Each of the 10 boards on this page is a real design using the LM5050-1. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the LM5050-1 VS pin connected?

The VS pin has a capacitor to GND on 8 of 9 designs, most often 100 nF. Counted from the KiCad layouts of 9 open source designs using the LM5050-1.

How is the LM5050-1 IN pin connected?

The IN pin has a capacitor to GND on 7 of 9 designs, most often 22 µF (then 47 µF). Counted from the KiCad layouts of 9 open source designs using the LM5050-1.

How is the LM5050-1 OUT pin connected?

The OUT pin is tied to 5V on 7 of 9 designs (a signal on 2). Counted from the KiCad layouts of 9 open source designs using the LM5050-1.

What parts are used alongside the LM5050-1?

The AP63205, SN74LVC1G125DBV, SN74LVC1G126DBVR, 74LVC1G08 and DNP-CAT24C32HU4 appear in the most repositories here.

Which microcontrollers do boards using the LM5050-1 use?

Most are built on ESP32 (2) and RP2040/RP2350 (2).

How big is a typical board using the LM5050-1?

The median is 65 × 30.9 mm, and 11% are two-layer designs.

What is the most popular open source board using the LM5050-1?

By GitHub stars, Elec RPI Robot HAT by pollen-robotics, with 108 stars.

Can I simulate one of these boards using the LM5050-1 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part