41 open source boards using the MCP4728
Real designs built with the MCP4728, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ZC95 MKII
CrashOverride85
191.5 × 76 mm319 parts2LGPL-3.0115AVR/Arduino
Power Supply (plus UBBB 32u4 rev 1.2)
thebiguno
99.1 × 99.1 mm189 parts2LNo license75BreadControlV3
Architeuthis-Flux
82.6 × 53.3 mm69 parts2LGPL-3.050ESP32
Endeavour2
petrmikheev
100 × 85 mm263 parts6LGPL-3.049STM32
STM32-Ethernet-Camera
DanielMartensson
100 × 100 mm140 parts4LMIT16RP2040/RP2350
HF PA Radio Interface
M0LTE
100 × 100 mm180 parts2LNo license15NXP
3DPCB
ChristianLerche
100 × 60 mm198 parts2LNo license9- schematic only · 10 partsAVR/Arduino
Korg ms20m extra midi2cv
retango
10 partsGPL-3.07 RP2040/RP2350
Opentrig
Dawson-HEP
162.2 × 100 mm408 parts4LEPL-2.06AFE
Blaze-Pascal
100 × 100 mm198 parts4LGPL-3.02NXP
3DPCB-4LAYER
ChristianLerche
100 × 60 mm200 parts4LNo license1RP2040/RP2350
HF PA Radio Interface
RADARC
100 × 100 mm180 parts2LNo license0NXP
PneuCNTRL2
hnnswldschtz
84.5 × 107.5 mm161 parts2LCustom license0Microchip SAM
Profane geometry
hearthsinger
61 × 76.2 mm131 parts4LCustom license0Power supply lt3571
burbschat
75 × 50 mm88 parts2LCERN-OHL-S-2.00Betr kicad resources
TheUnknownAlias
56.6 × 39 mm85 parts4LCustom license0CS107E Final Project PCBs
Rivercraft911
50 × 50 mm50 parts4LMIT0AVR/Arduino
Adjustable Modular Power Supply
thebiguno
36.8 × 52.7 mm183 parts2LNo license75AVR/Arduino
BreadControlV2-rounded 3
Architeuthis-Flux
82.6 × 53.3 mm58 parts2LGPL-3.050ESP32
Endeavour2 upd
petrmikheev
100 × 85 mm238 parts6LGPL-3.049AVR/Arduino
OutAna
radioelf
67.6 × 63.8 mm86 parts2LNo license7RP2040/RP2350
ControlBoard
ConfusedHello
76 × 76 mm27 parts2LNo license2FPGA
Robot
roman-khvatov
130 × 156 mm161 parts2LMIT1Lps regulator rev 12
jerryok826
136.2 × 62.6 mm122 parts2LMIT1AD8338 VGA
cnoikonom
79.3 × 47.5 mm56 parts4LMIT0Td rgbinput lm1205
tdaede
100 × 50 mm72 parts2LNo license370PanelControls
CrashOverride85
106 × 37.8 mm40 parts2LGPL-3.0115STM32
Midi-2-cv
lennartquerter
50 × 110 mm142 parts4LCC-BY-NC-4.012MCP4728 breakout board
6r1d
26.6 × 14.8 mm8 parts2LMIT2LaserDriverRGB
Rivercraft911
50 × 50 mm69 parts4LNo license1AVR/Arduino
Controller
ukmaker
99.7 × 70 mm26 parts2LNo license1RP2040/RP2350
Joystick DAC Board
scts-engineering
53.3 × 52.1 mm11 parts2LNo license112-bit analog outputs
wntrblm
27.1 × 24 mm30 parts2LCC-BY-SA-4.023ESP32
ESP32MIDI2CV v2
collaborative-music-lab
72 × 36 mm33 parts2LNo license19DAC-MCP4728
FluYVy
77 × 35 mm21 parts2LNo license1RP2040/RP2350
OLDintegrated joystick dac
scts-engineering
76.2 × 55.9 mm11 parts2LNo license1
How designs wire the MCP4728
Read from the KiCad layouts of 32 open source designs, one per repository: what each pin of the MCP4728 connects to, and the resistors, capacitors and other passives placed on it.
- The VDD pin has a decoupling capacitor on 22 of 32 designs, most often 100 nF (then 10 µF).
- The SCL pin has a pull-up to 3.3V on 20 of 32 designs, most often 4.7 kΩ (then 10 kΩ).
- The SDA pin has a pull-up to 3.3V on 20 of 32 designs, most often 4.7 kΩ (then 10 kΩ).
- The RDY/BSY pin is left unconnected on 24 of 32 designs (a signal on 7).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VDDpin 1 | Connected to: 3.3V 94% |
|
| SCLpin 2 | Connected to: The microcontroller 44%, a connector 38% |
|
| SDApin 3 | Connected to: The microcontroller 44%, a connector 41% |
|
| RDY/BSYpin 5 | Connected to: Not connected 75% · a signal 22% | — |
| VOUTApin 6 | Connected to: Signal 81% |
|
| VOUTBpin 7 | Connected to: Signal 81% |
|
| VOUTCpin 8 | Connected to: Signal 75% · not connected 16% |
|
| VOUTDpin 9 | Connected to: Signal 72% · not connected 16% |
|
| VSSpin 10 | Connected to: GND 94% | — |
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Td rgbinput lm1205 by tdaede, Zynface V5 by zynthian, ZC95 MKII by CrashOverride85 and Adjustable Modular Power Supply by thebiguno.
The MCP4728 in open source designs
The gallery holds 41 open source boards using the MCP4728 from 33 GitHub repositories; a typical one measures about 80.9 × 57.9 mm and carries around 85 components.
68% are two-layer designs, the rest use four layers or more, and 39% carry an open source license.
The most starred is Td rgbinput lm1205 by tdaede.
Parts used alongside the MCP4728
Microcontrollers on boards using the MCP4728
What boards using the MCP4728 are built for
MCP4728: common questions
Where can I find a MCP4728 reference design?
Each of the 41 boards on this page is a real design using the MCP4728. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the MCP4728 VDD pin?
The VDD pin has a decoupling capacitor on 22 of 32 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 32 open source designs using the MCP4728.
What pull-up resistor is used on the MCP4728 SCL pin?
The SCL pin has a pull-up to 3.3V on 20 of 32 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 32 open source designs using the MCP4728.
What pull-up resistor is used on the MCP4728 SDA pin?
The SDA pin has a pull-up to 3.3V on 20 of 32 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 32 open source designs using the MCP4728.
What parts are used alongside the MCP4728?
The 74AHCT125, 74LVC1G17, 74LVC74, ADS1015IDGS and AP2204K-ADJ appear in the most repositories here.
Which microcontrollers do boards using the MCP4728 use?
Most are built on RP2040/RP2350 (7), AVR/Arduino (6), ESP32 (4) and NXP (3).
How big is a typical board using the MCP4728?
The median is 80.9 × 57.9 mm, and 68% are two-layer designs.
What is the most popular open source board using the MCP4728?
By GitHub stars, Td rgbinput lm1205 by tdaede, with 370 stars.
Can I simulate one of these boards using the MCP4728 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.