32 open source boards using the 74HC595D
Real designs built with the 74HC595D, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Quad-AMBE3000
m1geo
84 × 62 mm192 parts4LMIT18ESP32
BlueJamma
KPEKEP
110.4 × 62.8 mm29 parts2LNo license3FPGA
Link
Jeo0
499.5 × 326 mm548 parts6LNo license2JoyMIDI-HW
bcc6
140 × 76.9 mm148 parts2LNo license2Dogrudan sdr C
kocer
350 × 235 mm392 parts2LNo license1AVR/Arduino
Lunar Writer
IlyaBOT
150 × 105 mm158 parts2LNo license0ESP32
Pinball Matrix board Rev 1
Phil-CIA
100 × 100 mm151 parts4LNo license0STM32
Robomas Controller board
ar216-2355
97.2 × 60 mm121 parts2LNo license0ESP32
Hat board
Phil-CIA
73.2 × 99.9 mm79 parts2LNo license0Solderbit segment shift edition
devices-lab
28 × 54 mm15 parts2LGPL-3.00G1000-partial panel-2
neilenns
100 × 100 mm2 parts2LNo license0- schematic only · 138 partsSTM32
Yuho vre1
shin-waseda
138 partsNo license0 FPGA
OLD-obfuscated-DontUse link
Jeo0
499.5 × 326 mm548 parts6LNo license2STM32
DSP-Regulator-HAT-RevB
Phil-CIA
100 × 102.6 mm158 parts2LNo license0ESP32
Pinball Matrix board Rev 1.kicad pcb pre route
Phil-CIA
100 × 100 mm151 parts2LNo license0AVR/Arduino
NM27C512 Dumper
IlyaBOT
141.9 × 88.7 mm130 parts2LNo license0ESP32
MuntsorteerderESP
TiebeDeclercq
52.8 × 69 mm51 parts2LNo license0Bumwings v001R64 xiao sd
tubbytwins
344.6 × 141.3 mm131 parts2LMIT22FPGA
Shematic1
Jeo0
246.5 × 189.3 mm527 parts4LNo license2Dogrudan sdr D
kocer
275 × 185 mm243 parts2LNo license1ESP32
DSP-Regulator-HAT-RevC
Phil-CIA
100 × 102.6 mm158 parts2LNo license0ESP32
Pinball Matrix board Rev 1 routed
Phil-CIA
100 × 100 mm148 parts4LNo license0RP2040/RP2350
Poc one
ItsShadowCone
95.5 × 108 mm141 parts2LNo license0AVR/Arduino
NM27C512 Dumper Lite
IlyaBOT
77.3 × 48 mm39 parts2LNo license0RP2040/RP2350
GlyphMatrix-128 Dual OLED and 8x8 LED Telemetry Badge
draarivpatel-ui
88 × 54 mm13 parts2LMIT0ESP32
Pinball Matrix board Rev 1 routed power
Phil-CIA
100 × 100 mm148 parts4LNo license0Poc one fpc
ItsShadowCone
95.5 × 108 mm141 parts2LNo license0ESP32
DSP Regulator hat
Phil-CIA
100 × 100 mm130 parts2LNo license0ESP32
Hat board
Phil-CIA
73.2 × 99.9 mm79 parts2LNo license0RP2040/RP2350
Backup
ItsShadowCone
125.5 × 116.7 mm122 parts2LNo license0Bumwings v001R55 xiao sd
tubbytwins
344.6 × 129.3 mm112 parts2LMIT22RP2040/RP2350
Transparent one
ItsShadowCone
275 × 200 mm79 parts2LNo license0
How designs wire the 74HC595D
Read from the KiCad layouts of 16 open source designs, one per repository: what each pin of the 74HC595D connects to, and the resistors, capacitors and other passives placed on it.
- The OE pin is tied to GND on 11 of 16 designs (a signal on 4).
- The VCC pin has a decoupling capacitor on 9 of 16 designs, most often 100 nF (then 100 µF).
- The Q1 pin has a series resistor on 7 of 16 designs, most often 1 kΩ (then 330 Ω).
- The Q2 pin has a series resistor on 7 of 16 designs, most often 1 kΩ (then 330 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Q1pin 1 | Connected to: Signal 100% |
|
| Q2pin 2 | Connected to: Signal 100% |
|
| Q3pin 3 | Connected to: Signal 100% |
|
| Q4pin 4 | Connected to: Signal 88% |
|
| Q5pin 5 | Connected to: Signal 88% |
|
| Q6pin 6 | Connected to: Signal 88% |
|
| GNDpin 8 | Connected to: GND 94% | — |
| OEpin 13 | Connected to: GND 69% · a signal 25% | — |
| Q0pin 15 | Connected to: Signal 94% |
|
| VCCpin 16 | Connected to: 3.3V 88% |
|
6 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Bumwings v001R55 xiao sd by tubbytwins, Quad-AMBE3000 by m1geo, BlueJamma by KPEKEP and JoyMIDI-HW by bcc6.
The 74HC595D in open source designs
The gallery holds 32 open source boards using the 74HC595D from 18 GitHub repositories; a typical one measures about 100 × 100 mm and carries around 140 components.
77% are two-layer designs, the rest use four layers or more, and 16% carry an open source license.
The most starred is Bumwings v001R64 xiao sd by tubbytwins.
Parts used alongside the 74HC595D
Microcontrollers on boards using the 74HC595D
What boards using the 74HC595D are built for
74HC595D: common questions
Where can I find a 74HC595D reference design?
Each of the 32 boards on this page is a real design using the 74HC595D. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the 74HC595D OE pin connected?
The OE pin is tied to GND on 11 of 16 designs (a signal on 4). Counted from the KiCad layouts of 16 open source designs using the 74HC595D.
What decoupling capacitors do designs use on the 74HC595D VCC pin?
The VCC pin has a decoupling capacitor on 9 of 16 designs, most often 100 nF (then 100 µF). Counted from the KiCad layouts of 16 open source designs using the 74HC595D.
What resistor goes on the 74HC595D Q1 pin?
The Q1 pin has a series resistor on 7 of 16 designs, most often 1 kΩ (then 330 Ω). Counted from the KiCad layouts of 16 open source designs using the 74HC595D.
What parts are used alongside the 74HC595D?
The W25Q128, 74HC165D, AMS1117-3.3, CH340C and MAX98357A appear in the most repositories here.
Which microcontrollers do boards using the 74HC595D use?
Most are built on ESP32 (10), RP2040/RP2350 (4), AVR/Arduino (3) and FPGA (3).
How big is a typical board using the 74HC595D?
The median is 100 × 100 mm, and 77% are two-layer designs.
What is the most popular open source board using the 74HC595D?
By GitHub stars, Bumwings v001R64 xiao sd by tubbytwins, with 22 stars.
Can I simulate one of these boards using the 74HC595D before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.