29 open source boards using the AP64501SP-13
Real designs built with the AP64501SP-13, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Oomwoo
makerspet
146.1 × 105.2 mm380 parts4LApache-2.042Astra piNas
jlcjak
100 × 120 mm176 parts6LNo license29RP2040/RP2350
Pedalboard hw
pedalboard
174 × 111 mm142 parts2LCERN-OHL-P-2.014Raspberry Pi
CM4IOv5-clone
sergiomd4
160 × 90 mm137 parts4LCC0-1.010Raspberry Pi
Unifying
balthazar-space
120.9 × 78.8 mm121 parts4LCERN-OHL-S-2.07Raspberry Pi
Matarael
h3430
160 × 90 mm137 parts4LNo license3STM32
CM4IOv5
DevCyclonekitten
160 × 90 mm137 parts4LGPL-3.02Raspberry Pi
Granit
laenzlinger
92 × 99.5 mm102 parts4LCERN-OHL-P-2.02Voight-Kampff
kampff
84 × 60 mm77 parts4LCC0-1.02Raspberry Pi
Raspberry-Pi-Hat for-AstroArch
FireNWater
86.5 × 56.5 mm31 parts2LNo license2ESP32
Chainaxe
johnny9
100 × 70 mm109 parts4LCERN-OHL-S-2.01STM32
Dual Axis Controller
jrseti
140 × 100 mm307 parts4LCC0-1.00STM32
RCM DishControllerBoard
jrseti
140 × 100 mm304 parts4LMIT0Raspberry Pi
CrallyBoard
cruunnerr
180.7 × 143.8 mm226 parts2LNo license0ESP32
AWS PROJECT
marydovika
206.3 × 91.3 mm207 parts2LNo license0Raspberry Pi
CM4IOv5
JRavenelco
160 × 90 mm137 parts4LNo license0NavPoTS-South
RuberDuck9
58.9 × 58.9 mm106 parts4LAGPL-3.00PiPowerNew
stephendade
65 × 30 mm53 parts4LCERN-OHL-S-2.00Raspberry Pi
CM4IOv5
wang-edward
160 × 90 mm137 parts4LMIT5Raspberry Pi
Cm4-printing deck
mothenjoyer69
100.4 × 92.9 mm84 parts4LMIT1Raspberry Pi
CM4IOUSB3
leesanghun-droid
160 × 90 mm141 parts4LNo license0ESP32
CanSat2
budabalint
40 × 40 mm102 parts4LNo license0AVR/Arduino
FlySensei Stack RPi
denjos007
90 × 65 mm89 parts4LNo license0Raspberry Pi
Psu
NBence0
140 × 70 mm243 parts6LNo license0RP2040/RP2350
CM4IOv5
raybello
160 × 90 mm137 parts4LNo license0Raspberry Pi
CM4IOv5
leesanghun-droid
160 × 90 mm137 parts4LNo license0CM5IO
NBence0
120.1 × 70.2 mm241 parts6LNo license0Raspberry Pi
AP2100v4
imagestream
160 × 90 mm137 parts4LMIT1Raspberry Pi
CM4IOv5
imagestream
160 × 90 mm137 parts4LMIT1
How designs wire the AP64501SP-13
Read from the KiCad layouts of 26 open source designs, one per repository: what each pin of the AP64501SP-13 connects to, and the resistors, capacitors and other passives placed on it.
- The BST pin has a series capacitor on 26 of 26 designs, most often 100 nF.
- The SS pin has a capacitor to GND on 26 of 26 designs, most often 100 nF (then 10 nF).
- The COMP pin has a series resistor on 26 of 26 designs, most often 20 kΩ (then 12 kΩ).
- The VIN pin has a decoupling capacitor on 25 of 26 designs, most often 10 µF (then 100 nF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| BSTpin 1 | Connected to: Signal 100% |
|
| VINpin 2 | Connected to: 12V 73% · a signal 27% |
|
| ENpin 3 | Connected to: 12V 65% · a signal 31% | — |
| SSpin 4 | Connected to: Signal 100% |
|
| FBpin 5 | Connected to: Signal 96% |
|
| COMPpin 6 | Connected to: Signal 100% |
|
| GNDpin 7 | Connected to: GND 100% | — |
| SWpin 8 | Connected to: Signal 96% |
|
| EPpin 9 | Connected to: GND 92% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Oomwoo pcb by makerspet, Astra piNas by jlcjak, Pedalboard hw by pedalboard and CM4IOv5-clone by sergiomd4.
The AP64501SP-13 in open source designs
The gallery holds 29 open source boards using the AP64501SP-13 from 26 GitHub repositories; a typical one measures about 140 × 90 mm and carries around 137 components.
86% use four copper layers or more, and 55% carry an open source license.
The most starred is Oomwoo pcb by makerspet.
Parts used alongside the AP64501SP-13
Microcontrollers on boards using the AP64501SP-13
What boards using the AP64501SP-13 are built for
AP64501SP-13: common questions
Where can I find a AP64501SP-13 reference design?
Each of the 29 boards on this page is a real design using the AP64501SP-13. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the AP64501SP-13 BST pin connected?
The BST pin has a series capacitor on 26 of 26 designs, most often 100 nF. Counted from the KiCad layouts of 26 open source designs using the AP64501SP-13.
How is the AP64501SP-13 SS pin connected?
The SS pin has a capacitor to GND on 26 of 26 designs, most often 100 nF (then 10 nF). Counted from the KiCad layouts of 26 open source designs using the AP64501SP-13.
What resistor goes on the AP64501SP-13 COMP pin?
The COMP pin has a series resistor on 26 of 26 designs, most often 20 kΩ (then 12 kΩ). Counted from the KiCad layouts of 26 open source designs using the AP64501SP-13.
What parts are used alongside the AP64501SP-13?
The FSUSB42MUX, RT9742GGJ5, 74LVC1G07SE-7, TPD4EUSB30 and USB2514B-I/M2 appear in the most repositories here.
Which microcontrollers do boards using the AP64501SP-13 use?
Most are built on Raspberry Pi (14), STM32 (4), ESP32 (3) and RP2040/RP2350 (2).
How big is a typical board using the AP64501SP-13?
The median is 140 × 90 mm, and 14% are two-layer designs.
What is the most popular open source board using the AP64501SP-13?
By GitHub stars, Oomwoo pcb by makerspet, with 42 stars.
Can I simulate one of these boards using the AP64501SP-13 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.