39 open source boards using the USB2514B-I/M2
Real designs built with the USB2514B-I/M2, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Raspberry Pi
Wall Panel
dotstartech
75 × 79 mm99 parts8LCERN-OHL-W-2.0366Raspberry Pi
CM4IOv5-clone
sergiomd4
160 × 90 mm137 parts4LCC0-1.010Tangenta
vmetodiev
243.8 × 243.8 mm534 parts4LCERN-OHL-P-2.05Raspberry Pi
Matarael
h3430
160 × 90 mm137 parts4LNo license3STM32
CM4IOv5
DevCyclonekitten
160 × 90 mm137 parts4LGPL-3.02STM32
Atlas drive
AtlasAutoware
140 × 90 mm377 parts6LNo license0STM32
Dual Axis Controller
jrseti
140 × 100 mm307 parts4LCC0-1.00STM32
RCM DishControllerBoard
jrseti
140 × 100 mm304 parts4LMIT0ESP32
Felső panel
NBence0
120.1 × 70.2 mm274 parts6LNo license0Raspberry Pi
CrallyBoard
cruunnerr
180.7 × 143.8 mm226 parts2LNo license0AVR/Arduino
HAT CM4 183
ConnectBox
105.6 × 86.1 mm161 parts6LNo license0RP2040/RP2350
UMMTJ Mainboard
vamatis
100 × 100 mm142 parts4LNo license0Raspberry Pi
Fable sbc test
geilevideossos-gamedev
100 × 74 mm138 parts4LGPL-3.00Raspberry Pi
CM4IOv5
JRavenelco
160 × 90 mm137 parts4LNo license0Raspberry Pi
Esp
jayadeep14
86.5 × 64.8 mm91 parts2LNo license0Raspberry Pi
Roboclaw cm4-dc dish controller
jrseti
145.8 × 76.9 mm49 parts2LMIT0- schematic only · 369 partsRaspberry Pi
PiCubed
NeilKhera
369 parts2LNo license0 Canjay
atopile
122 × 100 mm152 parts6LMIT29Raspberry Pi
CM4IOv5
wang-edward
160 × 90 mm137 parts4LMIT5ESP32
Board r0.turbocase
knewter
102.7 × 91.4 mm53 parts6LNo license2ESP32
High speed
NBence0
140 × 70 mm259 parts6LNo license0AVR/Arduino
HAT CM4 DRC 1
ConnectBox
105.6 × 86.1 mm147 parts6LNo license0Raspberry Pi
Cm4-robo controller
jrseti
145.8 × 76.9 mm49 parts2LCC0-1.00Hil core
atopile
1.5 × 9.6 mm114 parts4LMIT29ESP32
Board r1.turbocase
knewter
102.7 × 91.4 mm53 parts6LNo license2Raspberry Pi
CM4IOv5
leesanghun-droid
160 × 90 mm137 parts4LNo license0AVR/Arduino
ConnectBox HAT using RPi CM4
ConnectBox
105 × 78 mm130 parts4LNo license0ESP32
Board r2.turbocase
knewter
102.7 × 91.4 mm53 parts6LNo license2ESP32
Board r3.turbocase
knewter
102.7 × 91.4 mm53 parts6LNo license2ESP32
Board r4.turbocase
knewter
102.7 × 91.4 mm53 parts6LNo license2Raspberry Pi
AP2100v4
imagestream
160 × 90 mm137 parts4LMIT1Raspberry Pi
CM4IOv5
NBence0
160 × 90 mm137 parts4LNo license0ESP32
Board.turbocase
knewter
102.7 × 91.4 mm53 parts6LNo license2Raspberry Pi
CM4IOv5
imagestream
160 × 90 mm137 parts4LMIT1Robot fő nyák
NBence0
100.5 × 100.4 mm71 parts2LNo license0ESP32
Kvm carrier fanout
knewter
102.7 × 91.4 mm53 parts6LNo license2
How designs wire the USB2514B-I/M2
Read from the KiCad layouts of 21 open source designs, one per repository: what each pin of the USB2514B-I/M2 connects to, and the resistors, capacitors and other passives placed on it.
- The XTALOUT pin has a crystal on 19 of 19 designs, most often 24 MHz.
- The XTALIN/CLKIN pin has a crystal on 19 of 19 designs, most often 24 MHz.
- The RBIAS pin has a resistor to GND on 19 of 19 designs, most often 12 kΩ.
- The SUSP_IND/LOCAL_PWR/NON_R pin has a resistor to GND on 18 of 19 designs, most often 36 kΩ (then 100 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VDDA33pin 5, 10, 29, 36 | Connected to: 3.3V 83% · a signal 17% |
|
| TESTpin 11 | Connected to: Not connected 84% · GND 16% | — |
| CRFILTpin 14 | Connected to: Not connected 79% · a signal 21% | — |
| VDD33pin 15, 23 | Connected to: 3.3V 89% |
|
| PRTPWR2/BC_EN2pin 16 | Connected to: Not connected 89% | — |
| PRTPWR3/BC_EN3pin 18 | Connected to: Not connected 95% | — |
| PRTPWR4/BC_EN4pin 20 | Connected to: Not connected 95% | — |
| SDA/SMBDATA/NON_REM1pin 22 | Connected to: Signal 95% |
|
| SCL/SMBCLK/CFG_SEL0pin 24 | Connected to: Signal 95% |
|
| HS_IND/CFG_SEL1pin 25 | Connected to: Signal 95% |
|
| VBUS_DETpin 27 | Connected to: 3.3V 74% · a signal 26% |
|
| SUSP_IND/LOCAL_PWR/NON_Rpin 28 | Connected to: Signal 100% |
|
| XTALOUTpin 32 | Connected to: Signal 100% |
|
| XTALIN/CLKINpin 33 | Connected to: Signal 100% |
|
| PLLFILTpin 34 | Connected to: Not connected 79% · a signal 21% | — |
| RBIASpin 35 | Connected to: Signal 100% |
|
| VSSpin 37 | Connected to: GND 100% | — |
16 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Wall Panel by dotstartech, Canjay by atopile, CM4IOv5-clone by sergiomd4 and Tangenta by vmetodiev.
The USB2514B-I/M2 in open source designs
The gallery holds 39 open source boards using the USB2514B-I/M2 from 22 GitHub repositories; a typical one measures about 120 × 90 mm and carries around 137 components.
85% use four copper layers or more, and 36% carry an open source license.
The most starred is Wall Panel by dotstartech.
Parts used alongside the USB2514B-I/M2
Microcontrollers on boards using the USB2514B-I/M2
What boards using the USB2514B-I/M2 are built for
USB2514B-I/M2: common questions
Where can I find a USB2514B-I/M2 reference design?
Each of the 39 boards on this page is a real design using the USB2514B-I/M2. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the USB2514B-I/M2 XTALOUT pin connected?
The XTALOUT pin has a crystal on 19 of 19 designs, most often 24 MHz. Counted from the KiCad layouts of 21 open source designs using the USB2514B-I/M2.
How is the USB2514B-I/M2 XTALIN/CLKIN pin connected?
The XTALIN/CLKIN pin has a crystal on 19 of 19 designs, most often 24 MHz. Counted from the KiCad layouts of 21 open source designs using the USB2514B-I/M2.
What resistor goes on the USB2514B-I/M2 RBIAS pin?
The RBIAS pin has a resistor to GND on 19 of 19 designs, most often 12 kΩ. Counted from the KiCad layouts of 21 open source designs using the USB2514B-I/M2.
What parts are used alongside the USB2514B-I/M2?
The FSUSB42MUX, 74LVC1G07SE-7, TPD4EUSB30, AP22653W6 and AP64501SP-13 appear in the most repositories here.
Which microcontrollers do boards using the USB2514B-I/M2 use?
Most are built on Raspberry Pi (15), ESP32 (12), STM32 (4) and AVR/Arduino (3).
How big is a typical board using the USB2514B-I/M2?
The median is 120 × 90 mm, and 15% are two-layer designs.
What is the most popular open source board using the USB2514B-I/M2?
By GitHub stars, Wall Panel by dotstartech, with 366 stars.
Can I simulate one of these boards using the USB2514B-I/M2 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.