41 open source boards using the AP22653W6

Real designs built with the AP22653W6, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

41 boardsClear filters|Most starred

How designs wire the AP22653W6

Read from the KiCad layouts of 29 open source designs, one per repository: what each pin of the AP22653W6 connects to, and the resistors, capacitors and other passives placed on it.

  • The ILIM pin has a resistor to GND on 28 of 29 designs, most often 15 kΩ (then 49.9 kΩ).
  • The IN pin is tied to 5V on 27 of 29 designs (a signal on 2).
  • The OUT pin is tied to VBUS on 24 of 29 designs (a signal on 5).
  • The EN pin is tied to VBUS_EN on 18 of 29 designs (a signal on 10).
INpin 1Connected to: 5V 93%
GNDpin 2Connected to: GND 97%
ENpin 3Connected to: VBUS_EN 62% · a signal 34%
NFAULTpin 4Connected to: Not connected 62% · a signal 38%
ILIMpin 5Connected to: Signal 100%
  • Resistor to GND on 97% · 15 kΩ (27), 49.9 kΩ (1)
OUTpin 6Connected to: VBUS 83% · a signal 17%

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Wall Panel by dotstartech, CM5 MINIMA by claynicholson, Rpi cm5io mini itx by sanctuary-systems-com and Libreboard by 256foundation.

The AP22653W6 in open source designs

The gallery holds 41 open source boards using the AP22653W6 from 30 GitHub repositories; a typical one measures about 160 × 90 mm and carries around 91 components.

90% use four copper layers or more, and 46% carry an open source license.

The most starred is Wall Panel by dotstartech.

Microcontrollers on boards using the AP22653W6

AP22653W6: common questions

Where can I find a AP22653W6 reference design?

Each of the 41 boards on this page is a real design using the AP22653W6. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What resistor goes on the AP22653W6 ILIM pin?

The ILIM pin has a resistor to GND on 28 of 29 designs, most often 15 kΩ (then 49.9 kΩ). Counted from the KiCad layouts of 29 open source designs using the AP22653W6.

How is the AP22653W6 IN pin connected?

The IN pin is tied to 5V on 27 of 29 designs (a signal on 2). Counted from the KiCad layouts of 29 open source designs using the AP22653W6.

How is the AP22653W6 OUT pin connected?

The OUT pin is tied to VBUS on 24 of 29 designs (a signal on 5). Counted from the KiCad layouts of 29 open source designs using the AP22653W6.

What parts are used alongside the AP22653W6?

The TPD4EUSB30, RT9742SNGV, RT9742GGJ5, MagJack-A70-112-331N126 and 74LVC1G07SE-7 appear in the most repositories here.

Which microcontrollers do boards using the AP22653W6 use?

Most are built on Raspberry Pi (34), ESP32 (2), RP2040/RP2350 (1) and STM32 (1).

How big is a typical board using the AP22653W6?

The median is 160 × 90 mm, and 10% are two-layer designs.

What is the most popular open source board using the AP22653W6?

By GitHub stars, Wall Panel by dotstartech, with 366 stars.

Can I simulate one of these boards using the AP22653W6 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part