31 open source boards using the DRV2605LDGSR

Real designs built with the DRV2605LDGSR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

31 boardsClear filters|Most starred

How designs wire the DRV2605LDGSR

Read from the KiCad layouts of 11 open source designs, one per repository: what each pin of the DRV2605LDGSR connects to, and the resistors, capacitors and other passives placed on it.

  • The REG_1 pin has a capacitor to GND on 10 of 11 designs, most often 1 µF.
  • The VDD_10 pin has a decoupling capacitor on 9 of 11 designs, most often 100 nF (then 1 µF).
  • The IN/TRIG_4 pin is tied to GND on 9 of 11 designs.
  • The SCL_2 pin has a pull-up to 3.3V on 7 of 11 designs, most often 4.7 kΩ (then 5.1 kΩ).
REG_1pin 1Connected to: Signal 100%
  • Capacitor to GND on 91% · 1 µF (9)
SCL_2pin 2Connected to: The microcontroller 45%, a connector 27%
  • Pull-up to 3.3V on 64% · 4.7 kΩ (3), 5.1 kΩ (1), 1 kΩ (1)
SDA_3pin 3Connected to: The microcontroller 45%
  • Pull-up to 3.3V on 64% · 4.7 kΩ (3), 5.1 kΩ (1), 1 kΩ (1)
IN/TRIG_4pin 4Connected to: GND 82%
VDD/NC_6pin 6Connected to: 3.3V 64% · not connected 18% · a signal 18%
  • Decoupling capacitor on 55% · 100 nF (6), 1 µF (4)
GND_8pin 8Connected to: GND 91%
VDD_10pin 10Connected to: 3.3V 82% · a signal 18%
  • Decoupling capacitor on 82% · 100 nF (7), 1 µF (5), 10 µF (1)

3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Kompic Mk1 by porupski, Carrier by bhadkamkar9snehil, Wand by JMET04 and K2601-Doomsday-Comms-System by MixedSignalDevelopment.

The DRV2605LDGSR in open source designs

The gallery holds 31 open source boards using the DRV2605LDGSR from 16 GitHub repositories; a typical one measures about 29.6 × 42 mm and carries around 61 components.

79% use four copper layers or more, and 71% carry an open source license.

The most starred is Kompic Mk1b by porupski.

Microcontrollers on boards using the DRV2605LDGSR

DRV2605LDGSR: common questions

Where can I find a DRV2605LDGSR reference design?

Each of the 31 boards on this page is a real design using the DRV2605LDGSR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the DRV2605LDGSR REG_1 pin connected?

The REG_1 pin has a capacitor to GND on 10 of 11 designs, most often 1 µF. Counted from the KiCad layouts of 11 open source designs using the DRV2605LDGSR.

What decoupling capacitors do designs use on the DRV2605LDGSR VDD_10 pin?

The VDD_10 pin has a decoupling capacitor on 9 of 11 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 11 open source designs using the DRV2605LDGSR.

How is the DRV2605LDGSR IN/TRIG_4 pin connected?

The IN/TRIG_4 pin is tied to GND on 9 of 11 designs. Counted from the KiCad layouts of 11 open source designs using the DRV2605LDGSR.

What parts are used alongside the DRV2605LDGSR?

The LSM6DS3TR-C, USBLC6-2SC6, BMI270, BQ25185DLHR and ESP32-S3-WROOM-1 appear in the most repositories here.

Which microcontrollers do boards using the DRV2605LDGSR use?

Most are built on Nordic nRF (16), ESP32 (8) and STM32 (2).

How big is a typical board using the DRV2605LDGSR?

The median is 29.6 × 42 mm, and 21% are two-layer designs.

What is the most popular open source board using the DRV2605LDGSR?

By GitHub stars, Kompic Mk1b by porupski, with 3 stars.

Can I simulate one of these boards using the DRV2605LDGSR before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part