51 open source boards using the MCP6002
Real designs built with the MCP6002, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
OpenLaserScanningMicroscope
GaudiLabs
144 × 80 mm72 parts2LGPL-3.0342Analog rev3
PaulStoffregen
50.8 × 108 mm200 parts2LNo license160STM32
Guitarboard
JonasNorling
49.7 × 49.7 mm86 parts2LMIT97RP2040/RP2350
4HPico
rheslip
20.3 × 110 mm71 parts2LNo license83PedalPiV2
thawney
72.4 × 91.4 mm47 parts2LGPL-3.044AVR/Arduino
Foundation
odeliy
48 × 110 mm123 parts2LNo license37ESP8266
ESPlant
CCHS-Melbourne
97 × 77.5 mm75 parts2LTAPR-OHL-1.037ESP32
Iotuz esp32-hardware
CCHS-Melbourne
150 × 95 mm97 parts2LTAPR-OHL-1.035NXP
RawWaves
SherpaModular
20 × 107 mm55 parts2LNo license26NXP
Fjol
hallmar
184.7 × 110.7 mm204 parts2LNo license21STM32
Allcolours
microresearch
101.3 × 106.2 mm246 partsNo license15NXP
CAN-CCD bus
xerootg
107.7 × 85.1 mm83 parts2LNo license12STM32
KiCad
dirktjantele
172 parts6LGPL-3.09Drone o tron 1 0Rev1
koNrand
161.8 × 100 mm99 parts2LNo license7RP2040/RP2350
HF-PA-v10
kholia
90 × 99.9 mm97 parts2LGPL-3.06STM32
Quango Components
dchwebb
80.8 × 100 mm187 parts4LNo license5AVR/Arduino
Intercom
ukmaker
100 × 100 mm82 parts2LMIT5STM32
ActiveLoad
ahessling
50 × 100 mm75 parts2LMIT5RISC-V
Demiurge
AwesomeAudioApparatus
40.1 × 109.9 mm151 parts2LApache-2.04KicadExample
synthetos
51.1 × 38.1 mm80 parts2LNo license3DaisyDelayHardware
fablabnk
30 × 128.5 mm53 parts2LNo license3Simple synth
DJ027X
153.6 × 153.9 mm49 parts2LGPL-3.01AVR/Arduino
Pid smt oven retry
ntchris
71.1 × 49.3 mm48 parts2LGPL-3.01NXP
Guitar build
oo-eric
82 × 156 mm48 parts2LNo license1- schematic only · 31 partsTI MSP430/CC
Liu
liuwanwan1
31 partsNo license1 ESP32
Serrasoid TRX 29M
kazushinjo
170 × 150 mm328 parts4LGPL-3.00FPGA
X16-fpga board
eshankiyer
100 × 100 mm215 parts4LNo license0Caryatid
ideocentric
150 × 90 mm128 parts2LCERN-OHL-S-2.00AVR/Arduino
Imac
jreus
90 × 67 mm73 parts2LNo license0Kicker Board (Initial design by A Ryll -Tigers)
LiU-SeeGoals
140 × 85.4 mm63 parts2LNo license0NXP
Quadrants
nebularnoise
107.5 × 19.5 mm45 parts4LNo license0ESP32
HridayMitra
aadityaa0523
70 × 50 mm31 parts2LMIT0Mutant-SMD
soggybag
65.3 × 100 mm29 parts2LNo license0RP2040/RP2350
AS3397 eurorack 0603
PhysicsDptAngers
92.2 × 64.2 mm110 parts2LMIT87AVR/Arduino
Paradox
odeliy
38 × 110 mm114 parts2LNo license37Fjol top
hallmar
91.3 × 110.7 mm134 parts2LNo license21
How designs wire the MCP6002
Read from the KiCad layouts of 36 open source designs, one per repository: what each pin of the MCP6002 connects to, and the resistors, capacitors and other passives placed on it.
- The V+ pin has a decoupling capacitor on 28 of 36 designs, most often 100 nF (then 10 µF).
- The V- pin is tied to GND on 92% of them (-5V on 2).
- The OUT pins have a series resistor on 27 of 36 designs, most often 100 kΩ (then 1 kΩ).
- The - pins have a series resistor on 26 of 36 designs, most often 100 kΩ (then 10 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| OUTpin 1, 7 | Connected to: The microcontroller 21% |
|
| -pin 2, 6 | Connected to: Signal 83% |
|
| +pin 3, 5 | Connected to: Signal 69% · GND 19% |
|
| V-pin 4 | Connected to: GND 92% | — |
| V+pin 8 | Connected to: 3.3V 75% · a signal 25% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include OpenDropV4 by GaudiLabs, OpenLaserScanningMicroscope by GaudiLabs, Analog rev3 by PaulStoffregen and Drift by QuinnFreedman.
The MCP6002 in open source designs
The gallery holds 51 open source boards using the MCP6002 from 38 GitHub repositories; a typical one measures about 90 × 100 mm and carries around 82 components.
89% are two-layer designs, the rest use four layers or more, and 37% carry an open source license.
The most starred is OpenDropV4 by GaudiLabs.
Parts used alongside the MCP6002
Microcontrollers on boards using the MCP6002
What boards using the MCP6002 are built for
MCP6002: common questions
Where can I find a MCP6002 reference design?
Each of the 51 boards on this page is a real design using the MCP6002. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the MCP6002 V+ pin?
The V+ pin has a decoupling capacitor on 28 of 36 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 36 open source designs using the MCP6002.
How is the MCP6002 V- pin connected?
The V- pin is tied to GND on 92% of them (-5V on 2). Counted from the KiCad layouts of 36 open source designs using the MCP6002.
What resistor goes on the MCP6002 OUT pin?
The OUT pins have a series resistor on 27 of 36 designs, most often 100 kΩ (then 1 kΩ). Counted from the KiCad layouts of 36 open source designs using the MCP6002.
What parts are used alongside the MCP6002?
The MCP6004, TL072, AMS1117-3.3, TL074 and ADC122S051 appear in the most repositories here.
Which microcontrollers do boards using the MCP6002 use?
Most are built on AVR/Arduino (10), STM32 (9), RP2040/RP2350 (5) and NXP (5).
How big is a typical board using the MCP6002?
The median is 90 × 100 mm, and 89% are two-layer designs.
What is the most popular open source board using the MCP6002?
By GitHub stars, OpenDropV4 by GaudiLabs, with 487 stars.
Can I simulate one of these boards using the MCP6002 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.