42 open source boards using the SN74LVC1G14DBVR

Real designs built with the SN74LVC1G14DBVR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

42 boardsClear filters|Most starred

How designs wire the SN74LVC1G14DBVR

Read from the KiCad layouts of 23 open source designs, one per repository: what each pin of the SN74LVC1G14DBVR connects to, and the resistors, capacitors and other passives placed on it.

  • The VCC pin has a decoupling capacitor on 18 of 23 designs, most often 100 nF (then 10 µF).
  • The A pin has a series resistor on 11 of 23 designs, most often 1 kΩ (then 10 kΩ).
NCpin 1Connected to: Not connected 100%
Apin 2Connected to: A connector 22%
  • Series resistor on 48% · 1 kΩ (4), 10 kΩ (3), 18.7 kΩ (1)
  • Capacitor to GND on 35% · 10 nF (2), 100 nF (2), 1 µF (2)
GNDpin 3Connected to: GND 100%
Ypin 4Connected to: Signal 100%
  • Series resistor on 39% · 2.2 kΩ (2), 10 kΩ (2), 0 Ω (2)
VCCpin 5Connected to: 3.3V 83% · a signal 17%
  • Decoupling capacitor on 78% · 100 nF (33), 10 µF (3), 1 µF (2)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Rnvm marge by jaromir-sukuba, 65uino by AndersBNielsen, Moss by metrox-eth and CM5 MINIMA by claynicholson.

The SN74LVC1G14DBVR in open source designs

The gallery holds 42 open source boards using the SN74LVC1G14DBVR from 23 GitHub repositories; a typical one measures about 86 × 99.9 mm and carries around 197 components.

76% use four copper layers or more, and 21% carry an open source license.

The most starred is Rnvm marge by jaromir-sukuba.

Microcontrollers on boards using the SN74LVC1G14DBVR

SN74LVC1G14DBVR: common questions

Where can I find a SN74LVC1G14DBVR reference design?

Each of the 42 boards on this page is a real design using the SN74LVC1G14DBVR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What decoupling capacitors do designs use on the SN74LVC1G14DBVR VCC pin?

The VCC pin has a decoupling capacitor on 18 of 23 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 23 open source designs using the SN74LVC1G14DBVR.

What resistor goes on the SN74LVC1G14DBVR A pin?

The A pin has a series resistor on 11 of 23 designs, most often 1 kΩ (then 10 kΩ). Counted from the KiCad layouts of 23 open source designs using the SN74LVC1G14DBVR.

What parts are used alongside the SN74LVC1G14DBVR?

The TPS3808G01DBVR, USBLC6-2SC6, AP2112K-3.3TRG1, SN74LVC1G08DBVR and SN74LVC1G32DBVR appear in the most repositories here.

Which microcontrollers do boards using the SN74LVC1G14DBVR use?

Most are built on STM32 (4), ESP32 (3), Raspberry Pi (3) and RP2040/RP2350 (2).

How big is a typical board using the SN74LVC1G14DBVR?

The median is 86 × 99.9 mm, and 24% are two-layer designs.

What is the most popular open source board using the SN74LVC1G14DBVR?

By GitHub stars, Rnvm marge by jaromir-sukuba, with 459 stars.

Can I simulate one of these boards using the SN74LVC1G14DBVR before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part