38 open source boards using the TL084
Real designs built with the TL084, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Amiga-SMD-500
amigalisa
368.3 × 254 mm556 parts2LCERN-OHL-S-2.069STM32
Taiko-Input
AnalogDragon
85 × 100 mm235 parts2LCustom license16ESP32
Galvo
breqdev
200 × 50 mm84 parts2LNo license16STM32
OpenHand v3
AleksaHeler
100 × 50 mm181 parts4LMIT113310ADSR
hermflink
94.5 × 55 mm50 parts2LGPL-3.011Euclid Main Board
m0xpd
78 × 108 mm128 parts2LCC-BY-SA-4.07ESP32
TR-808 clone
mkomakonkon
442 × 421.7 mm1268 parts2LNo license5ESP32
Osciloscope-ESP32
cristobalcuevas
137.5 × 42.5 mm79 parts2LNo license4Zx specdrum re created
zxinfo-diy-electronics
76 × 51.4 mm29 parts2LNo license4Lab scale gantry crane
Cosys-Lab
68.6 × 53.3 mm22 parts2LMIT4Tda bridge
f4hpu
175.2 × 125.4 mm170 parts2LNo license3Class D Amp
zerberros
140.5 × 79 mm77 parts2LNo license3STM32
Light Commander
ethandrzb
70.2 × 108 mm163 parts6LNo license2Input Board
jensenr30
100 × 100 mm93 parts2LNo license1CarteAdaptatrice
IOGS-LEnsE-ressources
205.7 × 109.9 mm48 parts2LNo license1SoundLab16StepSequencer
JakeBoothy
314.9 × 110 mm348 parts4LNo license0STM32
OpenHand v3
iamprince3
100 × 50 mm181 parts4LNo license0Vca
eblade
99.1 × 99.1 mm104 parts2LNo license0EEG Prototype
diosey
81.6 × 96.4 mm55 parts2LGPL-3.00Raspberry Pi
Signal Conditioner
DanMartins
113.3 × 84.4 mm34 parts2LGPL-3.00TC2
MaximilianoMontenegro
100 × 50 mm31 parts2LNo license0EMG-MUSCLE-SENSOR
MAHESH-THILAK-K
39.1 × 47.7 mm22 parts2LMIT0Vca
nickajeglin
45.2 × 146.8 mm79 parts2LNo license208Vca
VincentPeters
45.2 × 146.8 mm79 parts2LNo license9Euclid Control Board
m0xpd
78 × 108 mm105 parts2LCC-BY-SA-4.07Input Board Panel
jensenr30
100 × 100 mm93 parts2LNo license1PCB Project
KVentayen
80 × 60 mm21 parts2LNo license0Nono Circuito SMD
EngTarcisioSm
30.5 × 36.2 mm16 parts2LNo license0Licht array
microresearch
78.7 × 64.8 mm67 parts2LNo license3Asst slave d25
IOGS-LEnsE-platforms
91.4 × 91.4 mm35 parts2LNo license0Dual VCA #2 Main
mzuelch
58.4 × 101.6 mm63 parts2LMIT166PIC
ExpEYES Junior
expeyes
54.5 × 81.5 mm103 parts2LNo license18AM modulation fiber
IOGS-LEnsE-platforms
88.9 × 66.6 mm32 parts2LNo license0Dz Mixer
dzavalishin
68.9 × 118.5 mm105 parts2LNo license3LabBooster
reivax-boucoi
74.8 × 69.5 mm79 parts2LNo license1Dz HeadPhones Amp
dzavalishin
76.2 × 69.9 mm79 parts2LNo license3
How designs wire the TL084
Read from the KiCad layouts of 33 open source designs, one per repository: what each pin of the TL084 connects to, and the resistors, capacitors and other passives placed on it.
- The OUT pins have a series resistor on 29 of 33 designs, most often 1 kΩ (then 2 kΩ).
- The - pins have a series resistor on 27 of 33 designs, most often 100 kΩ (then 2 kΩ).
- The + pins have a series resistor on 18 of 33 designs, most often 1 kΩ (then 100 kΩ).
- The + pins have a resistor to GND on 16 of 33 designs, most often 100 kΩ (then 2 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| OUTpin 1, 7, 8, 14 | Connected to: A connector 21% |
|
| -pin 2, 6, 9, 13 | Connected to: Signal 86% |
|
| +pin 3, 5, 10, 12 | Connected to: Signal 71% · GND 24% |
|
| V+pin 4 | Connected to: 12V 82% · a signal 18% |
|
| V-pin 11 | Connected to: -12V 64% · a signal 27% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Vca by nickajeglin, Dual VCA #2 Main by mzuelch, Amiga-SMD-500 by amigalisa and ExpEYES Junior by expeyes.
The TL084 in open source designs
The gallery holds 38 open source boards using the TL084 from 33 GitHub repositories; a typical one measures about 83.3 × 83 mm and carries around 79 components.
87% are two-layer designs, the rest use four layers or more, and 26% carry an open source license.
The most starred is Vca by nickajeglin.
Parts used alongside the TL084
Microcontrollers on boards using the TL084
What boards using the TL084 are built for
TL084: common questions
Where can I find a TL084 reference design?
Each of the 38 boards on this page is a real design using the TL084. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the TL084 OUT pin?
The OUT pins have a series resistor on 29 of 33 designs, most often 1 kΩ (then 2 kΩ). Counted from the KiCad layouts of 33 open source designs using the TL084.
What resistor goes on the TL084 - pin?
The - pins have a series resistor on 27 of 33 designs, most often 100 kΩ (then 2 kΩ). Counted from the KiCad layouts of 33 open source designs using the TL084.
What resistor goes on the TL084 + pin?
The + pins have a series resistor on 18 of 33 designs, most often 1 kΩ (then 100 kΩ). Counted from the KiCad layouts of 33 open source designs using the TL084.
What parts are used alongside the TL084?
The LM13700, 40106, TL082, 4013 and 74LS32 appear in the most repositories here.
Which microcontrollers do boards using the TL084 use?
Most are built on STM32 (4), ESP32 (3), PIC (1) and Raspberry Pi (1).
How big is a typical board using the TL084?
The median is 83.3 × 83 mm, and 87% are two-layer designs.
What is the most popular open source board using the TL084?
By GitHub stars, Vca by nickajeglin, with 208 stars.
Can I simulate one of these boards using the TL084 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.