24 open source boards using the TPS61040DBV

Real designs built with the TPS61040DBV, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

24 boardsClear filters|Most starred

How designs wire the TPS61040DBV

Read from the KiCad layouts of 16 open source designs, one per repository: what each pin of the TPS61040DBV connects to, and the resistors, capacitors and other passives placed on it.

  • The SW pin has a inductor on 14 of 16 designs, most often 10 µH (then 6.8 µH).
  • The FB pin has a resistor to GND on 14 of 16 designs, most often 205 kΩ (then 200 kΩ).
  • The VIN pin has a inductor on 14 of 16 designs, most often 10 µH (then 6.8 µH).
  • The VIN pin has a decoupling capacitor on 13 of 16 designs, most often 4.7 µF (then 10 µF).
SWpin 1Connected to: Signal 100%
  • Inductor on 88% · 10 µH (8), 6.8 µH (2), 22 µH (2)
GNDpin 2Connected to: GND 88%
FBpin 3Connected to: Signal 100%
  • Resistor to GND on 88% · 205 kΩ (2), 200 kΩ (2), 150 kΩ (2)
  • Pull-up to 12V on 75% · 1.8 MΩ (2), 1.5 MΩ (2), 1 MΩ (2)
  • Capacitor to the supply on 75% · 22 pF (3), 4.7 pF (2), 18 pF (2)
ENpin 4Connected to: VCC 63% · a signal 25%
  • Inductor on 63% · 10 µH (7), 1 µH (1), 3.3 µH (1)
VINpin 5Connected to: VCC 75% · a signal 19%
  • Inductor on 88% · 10 µH (8), 6.8 µH (2), 22 µH (2)
  • Decoupling capacitor on 81% · 4.7 µF (8), 10 µF (4), 47 µF (1)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include EinkPDA keyboard by TalismanDesign, Plinkyblack hwmidi jacks by plinkysynth, Module17 HMI by M17-Project and Corevus m by calithameridi.

The TPS61040DBV in open source designs

The gallery holds 24 open source boards using the TPS61040DBV from 16 GitHub repositories; a typical one measures about 98.5 × 89.1 mm and carries around 121 components.

58% use four copper layers or more, and 42% carry an open source license.

The most starred is EinkPDA keyboard by TalismanDesign.

Microcontrollers on boards using the TPS61040DBV

TPS61040DBV: common questions

Where can I find a TPS61040DBV reference design?

Each of the 24 boards on this page is a real design using the TPS61040DBV. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the TPS61040DBV SW pin connected?

The SW pin has a inductor on 14 of 16 designs, most often 10 µH (then 6.8 µH). Counted from the KiCad layouts of 16 open source designs using the TPS61040DBV.

What resistor goes on the TPS61040DBV FB pin?

The FB pin has a resistor to GND on 14 of 16 designs, most often 205 kΩ (then 200 kΩ). Counted from the KiCad layouts of 16 open source designs using the TPS61040DBV.

How is the TPS61040DBV VIN pin connected?

The VIN pin has a inductor on 14 of 16 designs, most often 10 µH (then 6.8 µH). Counted from the KiCad layouts of 16 open source designs using the TPS61040DBV.

What parts are used alongside the TPS61040DBV?

The XC6206P332MR, DAC7554IDGS, HCPL-0631, HCPL-0631-500E and LIS2DH12 appear in the most repositories here.

Which microcontrollers do boards using the TPS61040DBV use?

Most are built on ESP32 (7), STM32 (4), RP2040/RP2350 (2) and Nordic nRF (1).

How big is a typical board using the TPS61040DBV?

The median is 98.5 × 89.1 mm, and 42% are two-layer designs.

What is the most popular open source board using the TPS61040DBV?

By GitHub stars, EinkPDA keyboard by TalismanDesign, with 2,025 stars.

Can I simulate one of these boards using the TPS61040DBV before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part