22 open source boards using the EMC2101

Real designs built with the EMC2101, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

22 boardsClear filters|Most starred

How designs wire the EMC2101

Read from the KiCad layouts of 20 open source designs, one per repository: what each pin of the EMC2101 connects to, and the resistors, capacitors and other passives placed on it.

  • The FAN pin has a pull-up to 5V on 20 of 20 designs, most often 10 kΩ.
  • The ALERT/TACH pin has a pull-up to 3.3V on 20 of 20 designs, most often 5.6 kΩ.
  • The DP pin has a series capacitor on 13 of 20 designs, most often 470 pF.
  • The DP pin has a series resistor on 13 of 20 designs, most often 100 Ω (then 0 Ω).
VDDpin 1Connected to: 3.3V 100%
  • Decoupling capacitor on 40% · 100 nF (8)
DPpin 2Connected to: Signal 65% · not connected 35%
  • Series capacitor on 65% · 470 pF (13)
  • Series resistor on 65% · 100 Ω (12), 0 Ω (1)
DNpin 3Connected to: Signal 65% · not connected 35%
  • Series capacitor on 65% · 470 pF (13)
  • Series resistor on 65% · 100 Ω (12), 0 Ω (1)
FANpin 4Connected to: A connector 100%
  • Pull-up to 5V on 100% · 10 kΩ (20)
GNDpin 5Connected to: GND 100%
ALERT/TACHpin 6Connected to: A connector 100%
  • Pull-up to 3.3V on 100% · 5.6 kΩ (20)

2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Bitaxe by skot, BitaxeGamma by bitaxeorg, BitaxeSupra by bitaxeorg and BitaxeUltra by bitaxeorg.

The EMC2101 in open source designs

The gallery holds 22 open source boards using the EMC2101 from 20 GitHub repositories; a typical one measures about 56.5 × 99.8 mm and carries around 90 components.

95% use four copper layers or more, and 73% carry an open source license.

The most starred is Bitaxe by skot.

Microcontrollers on boards using the EMC2101

What boards using the EMC2101 are built for

EMC2101: common questions

Where can I find a EMC2101 reference design?

Each of the 22 boards on this page is a real design using the EMC2101. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What pull-up resistor is used on the EMC2101 FAN pin?

The FAN pin has a pull-up to 5V on 20 of 20 designs, most often 10 kΩ. Counted from the KiCad layouts of 20 open source designs using the EMC2101.

What pull-up resistor is used on the EMC2101 ALERT/TACH pin?

The ALERT/TACH pin has a pull-up to 3.3V on 20 of 20 designs, most often 5.6 kΩ. Counted from the KiCad layouts of 20 open source designs using the EMC2101.

How is the EMC2101 DP pin connected?

The DP pin has a series capacitor on 13 of 20 designs, most often 470 pF. Counted from the KiCad layouts of 20 open source designs using the EMC2101.

What parts are used alongside the EMC2101?

The ESP32-S3-WROOM-1, RT9080-33GJ5, 25MHZ, MCP1824T-0802E and TPS546D24ARVFR appear in the most repositories here.

Which microcontrollers do boards using the EMC2101 use?

Most are built on ESP32 (22).

How big is a typical board using the EMC2101?

The median is 56.5 × 99.8 mm, and 5% are two-layer designs.

What is the most popular open source board using the EMC2101?

By GitHub stars, Bitaxe by skot, with 1,375 stars.

Can I simulate one of these boards using the EMC2101 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part