31 open source boards using the INA260

Real designs built with the INA260, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

31 boardsClear filters|Most starred

How designs wire the INA260

Read from the KiCad layouts of 28 open source designs, one per repository: what each pin of the INA260 connects to, and the resistors, capacitors and other passives placed on it.

  • The VS pin has a decoupling capacitor on 21 of 27 designs, most often 100 nF (then 1 µF).
  • The A0 pin is tied to GND on 20 of 27 designs (not connected on 3, a signal on 3).
  • The A1 pin is tied to GND on 19 of 27 designs (not connected on 2, 3.3V on 2, a signal on 4).
  • The ALERT pin is left unconnected on 18 of 28 designs (GND on 2, a signal on 7).
A1pin 4Connected to: GND 70%
A0pin 5Connected to: GND 74%
GNDpin 6, 11Connected to: GND 96%
ALERTpin 7Connected to: Not connected 64% · a signal 25%
SDApin 8Connected to: The microcontroller 75%, DS4432U+ 29%, EMC2101 25%
  • Pull-up to 3.3V on 54% · 4.7 kΩ (10), 10 kΩ (2), 2.7 kΩ (1)
SCLpin 9Connected to: The microcontroller 78%, DS4432U+ 30%, EMC2101 26%
  • Pull-up to 3.3V on 56% · 4.7 kΩ (10), 10 kΩ (2), 2.7 kΩ (1)
VSpin 10Connected to: 3.3V 89%
  • Decoupling capacitor on 78% · 100 nF (12), 1 µF (10), 47 µF (1)
VBUSpin 12Connected to: VIN 62% · a signal 35%
NCpin 13Connected to: Not connected 100%

2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Open source rover by nasa-jpl, Bitaxe by skot, Emberone00-pcb by 256foundation and BitaxeUltra by bitaxeorg.

The INA260 in open source designs

The gallery holds 31 open source boards using the INA260 from 28 GitHub repositories; a typical one measures about 100 × 93.5 mm and carries around 92 components.

58% use four copper layers or more, and 42% carry an open source license.

The most starred is Open source rover by nasa-jpl.

Microcontrollers on boards using the INA260

INA260: common questions

Where can I find a INA260 reference design?

Each of the 31 boards on this page is a real design using the INA260. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What decoupling capacitors do designs use on the INA260 VS pin?

The VS pin has a decoupling capacitor on 21 of 27 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 28 open source designs using the INA260.

How is the INA260 A0 pin connected?

The A0 pin is tied to GND on 20 of 27 designs (not connected on 3, a signal on 3). Counted from the KiCad layouts of 28 open source designs using the INA260.

How is the INA260 A1 pin connected?

The A1 pin is tied to GND on 19 of 27 designs (not connected on 2, 3.3V on 2, a signal on 4). Counted from the KiCad layouts of 28 open source designs using the INA260.

What parts are used alongside the INA260?

The 25MHZ, ESP32-S3-WROOM-1, MCP1824T-0802E, DS4432U+ and EMC2101 appear in the most repositories here.

Which microcontrollers do boards using the INA260 use?

Most are built on ESP32 (14), STM32 (7), RP2040/RP2350 (2) and Microchip SAM (1).

How big is a typical board using the INA260?

The median is 100 × 93.5 mm, and 42% are two-layer designs.

What is the most popular open source board using the INA260?

By GitHub stars, Open source rover by nasa-jpl, with 9,675 stars.

Can I simulate one of these boards using the INA260 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part