33 open source boards using the ESP32-S3-WROOM-1-N16R2
Real designs built with the ESP32-S3-WROOM-1-N16R2, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
EinkPDA keyboard
TalismanDesign
95 × 55.5 mm128 parts4LApache-2.02.0kESP32
LHCbit
lhc
51.6 × 44.4 mm51 parts4LNo license6ESP32
Veramonitor
eigenlucy
137.2 × 120.1 mm47 parts2LMIT5ESP32
Teacup carrier
thingino
257 × 117.5 mm133 parts4LGPL-3.02ESP32
OrphBeatPad
Axe-1st
112.7 × 121.4 mm57 parts2LNo license2ESP32
Tresvizo main
cadaritre
36 × 71.5 mm106 parts4LNo license1ESP32
Dsp board
perrypetiet
101.1 × 49.3 mm91 parts2LNo license1ESP32
Low-Cost-Insulin-Pump-V2.1
mattgp32
32 × 45 mm82 parts4LNo license1ESP32
Mood-Display
Axe-1st
70.2 × 70.2 mm54 parts2LNo license1ESP32
E0005-esp32-s3-5v controller
Karpuls
125 × 73 mm268 parts4LNo license0ESP32
Kestrel controller
AthArvA-188
134 × 82 mm182 parts4LNo license0ESP32
Pace racer hardware
rammp-org
0 × 0 mm118 parts4LNo license0ESP32
ESP32-S3-4Layer-CoreBoard
gorkemguven
102.9 × 43.7 mm101 parts4LGPL-3.00ESP32
HouseholdWaterMonitoringSystem
Danielbaker31
89 × 45 mm92 parts2LNo license0ESP32
Light Jacket rev0 2 - Mousebites
loganma02
68 × 70 mm87 parts2LNo license0ESP32
Aquarius node hw
crgmakes
50 × 50 mm81 parts4LCC-BY-SA-4.00ESP32
Gdip test tube hardware
camerongrimes
76.2 × 58.5 mm72 parts2LNo license0ESP32
Citofono vintage
michele88pg
81 × 85 mm61 parts2LCC-BY-SA-4.00ESP32
LiquorBot
irozalski
58.5 × 87 mm36 parts4LNo license0ESP32
Shematic for power and light system
jasmehar
95.1 × 53.1 mm35 parts2LNo license0ESP32
ESP32-EFIS
rhine59
68 × 68 mm25 parts4LNo license0ESP32
Lhc tijolo32 board
lhc
24 × 84.5 mm44 parts2LNo license6ESP32
Teacup carrier merge test
thingino
257 × 117.5 mm131 parts4LGPL-3.02ESP32
Tresvizo panel
cadaritre
50 × 85.5 mm106 parts4LNo license1ESP32
Light Jacket rev0 21
loganma02
68 × 70 mm87 parts2LNo license0ESP32
MuntsorteerderESP
TiebeDeclercq
52.8 × 69 mm51 parts2LNo license0ESP32
Smart helmet
jasmehar
98.4 × 75.6 mm32 parts2LNo license0ESP32
Version1
meyerAurelius
60 × 57.8 mm16 parts4LNo license0ESP32
Masthead Controller
Tuskar-Marine
150 × 83 mm209 parts4LNo license6ESP32
Lhc esp
lhc
48.4 × 35.4 mm24 parts2LNo license6ESP32
Light Jacket rev0 2 - No Breakout
loganma02
55 × 70 mm78 parts2LNo license0ESP32
Placas
lhc
60 × 41.5 mm24 parts2LNo license6ESP32
N2K Transceiver
Tuskar-Marine
60 × 75 mm68 parts4LNo license6
How designs wire the ESP32-S3-WROOM-1-N16R2
Read from the KiCad layouts of 24 open source designs, one per repository: what each pin of the ESP32-S3-WROOM-1-N16R2 connects to, and the resistors, capacitors and other passives placed on it.
- The EN pin has a pull-up to 3.3V on 21 of 24 designs, most often 10 kΩ (then 100 kΩ).
- The EN pin has a capacitor to GND on 17 of 24 designs, most often 1 µF (then 100 nF).
- The 3V3 pin is tied to 3.3V on 18 of 24 designs (a signal on 5).
- The IO0 pin has a pull-up to 3.3V on 14 of 22 designs, most often 10 kΩ (then 100 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1, 40 | Connected to: GND 98% | — |
| 3V3pin 2 | Connected to: 3.3V 75% · a signal 21% | — |
| ENpin 3 | Connected to: Signal 100% |
|
| IO5pin 5 | Connected to: A connector 25% |
|
| IO0pin 27 | Connected to: Signal 100% |
|
| GND_41pin 41 | Connected to: GND 100% | — |
34 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include EinkPDA keyboard by TalismanDesign, Lhc esp by lhc, Masthead Controller by Tuskar-Marine and Veramonitor by eigenlucy.
The ESP32-S3-WROOM-1-N16R2 in open source designs
The gallery holds 33 open source boards using the ESP32-S3-WROOM-1-N16R2 from 24 GitHub repositories; a typical one measures about 68 × 70 mm and carries around 78 components.
52% use four copper layers or more, and 21% carry an open source license.
The most starred is EinkPDA keyboard by TalismanDesign.
Parts used alongside the ESP32-S3-WROOM-1-N16R2
Microcontrollers on boards using the ESP32-S3-WROOM-1-N16R2
What boards using the ESP32-S3-WROOM-1-N16R2 are built for
ESP32-S3-WROOM-1-N16R2: common questions
Where can I find a ESP32-S3-WROOM-1-N16R2 reference design?
Each of the 33 boards on this page is a real design using the ESP32-S3-WROOM-1-N16R2. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the ESP32-S3-WROOM-1-N16R2 EN pin?
The EN pin has a pull-up to 3.3V on 21 of 24 designs, most often 10 kΩ (then 100 kΩ). Counted from the KiCad layouts of 24 open source designs using the ESP32-S3-WROOM-1-N16R2.
How is the ESP32-S3-WROOM-1-N16R2 3V3 pin connected?
The 3V3 pin is tied to 3.3V on 18 of 24 designs (a signal on 5). Counted from the KiCad layouts of 24 open source designs using the ESP32-S3-WROOM-1-N16R2.
What pull-up resistor is used on the ESP32-S3-WROOM-1-N16R2 IO0 pin?
The IO0 pin has a pull-up to 3.3V on 14 of 22 designs, most often 10 kΩ (then 100 kΩ). Counted from the KiCad layouts of 24 open source designs using the ESP32-S3-WROOM-1-N16R2.
What parts are used alongside the ESP32-S3-WROOM-1-N16R2?
The AMS1117-3.3, USBLC6-2SC6, MAX17048G+T10 and USBLC6-2P6 appear in the most repositories here.
Which microcontrollers do boards using the ESP32-S3-WROOM-1-N16R2 use?
Most are built on ESP32 (33).
How big is a typical board using the ESP32-S3-WROOM-1-N16R2?
The median is 68 × 70 mm, and 48% are two-layer designs.
What is the most popular open source board using the ESP32-S3-WROOM-1-N16R2?
By GitHub stars, EinkPDA keyboard by TalismanDesign, with 2,025 stars.
Can I simulate one of these boards using the ESP32-S3-WROOM-1-N16R2 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.