26 open source boards using the TCRT5000

Real designs built with the TCRT5000, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

26 boardsClear filters|Most starred

How designs wire the TCRT5000

Read from the KiCad layouts of 19 open source designs, one per repository: what each pin of the TCRT5000 connects to, and the resistors, capacitors and other passives placed on it.

  • Pin A has a pull-up to 3.3V on 13 of 15 designs, most often 220 Ω (then 1 kΩ).
  • Pin E is tied to GND on 13 of 15 designs (a signal on 2).
  • Pin CATH is tied to GND on 12 of 15 designs (a signal on 2).
  • Pin COLL has a pull-up to 3.3V on 10 of 15 designs, most often 10 kΩ (then 4.7 kΩ).
Pin AConnected to: Signal 93%
  • Pull-up to 3.3V on 87% · 220 Ω (4), 1 kΩ (3), 150 Ω (1)
Pin CATHConnected to: GND 80%
Pin COLLConnected to: A connector 27%, LM393 20%
  • Pull-up to 3.3V on 67% · 10 kΩ (8), 4.7 kΩ (2), 2.4 kΩ (1)
Pin EConnected to: GND 87%

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Lsa by SRA-VJTI, ${PROJECT} by tobigun, Hardware by xtarke and Hardware by xtarke.

The TCRT5000 in open source designs

The gallery holds 26 open source boards using the TCRT5000 from 21 GitHub repositories; a typical one measures about 104.8 × 56.2 mm and carries around 42 components.

92% are two-layer designs, the rest use four layers or more, and 50% carry an open source license.

The most starred is Lsa by SRA-VJTI.

Microcontrollers on boards using the TCRT5000

TCRT5000: common questions

Where can I find a TCRT5000 reference design?

Each of the 26 boards on this page is a real design using the TCRT5000. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What pull-up resistor is used on the TCRT5000 pin A?

Pin A has a pull-up to 3.3V on 13 of 15 designs, most often 220 Ω (then 1 kΩ). Counted from the KiCad layouts of 19 open source designs using the TCRT5000.

How is the TCRT5000 pin E connected?

Pin E is tied to GND on 13 of 15 designs (a signal on 2). Counted from the KiCad layouts of 19 open source designs using the TCRT5000.

How is the TCRT5000 pin CATH connected?

Pin CATH is tied to GND on 12 of 15 designs (a signal on 2). Counted from the KiCad layouts of 19 open source designs using the TCRT5000.

What parts are used alongside the TCRT5000?

The LM393, AMS1117-3.3, HC-05, HC-SR04 and L293D appear in the most repositories here.

Which microcontrollers do boards using the TCRT5000 use?

Most are built on ESP32 (3), AVR/Arduino (1) and STM32 (1).

How big is a typical board using the TCRT5000?

The median is 104.8 × 56.2 mm, and 92% are two-layer designs.

What is the most popular open source board using the TCRT5000?

By GitHub stars, Lsa by SRA-VJTI, with 80 stars.

Can I simulate one of these boards using the TCRT5000 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part