23 open source boards using the SMF05CT1G
Real designs built with the SMF05CT1G, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
GPS-Tracker
mohamedboubaker
35 × 53 mm53 parts2LNo license40RP2040/RP2350
YM60JIS
ymkn
285.1 × 94.6 mm165 parts2LMIT9STM32
Scorpion card pub
psk7
83.1 × 45.4 mm88 parts2LMIT7RP2040/RP2350
Low profile with trackball
ryoo14
228.8 × 76.2 mm137 parts2LNo license3STM32
GPS-Tracker
ibfarhat
35 × 53 mm53 parts2LNo license3ESP8266
UnderControl Hardware Design
YamanSeyravan
100 × 100 mm185 parts4LGPL-3.02STM32
Bluegrass
agrif
61 × 88.9 mm107 parts4LCC-BY-SA-4.02STM32
KICAD-STM32-GPS-Tracker-Project
Saie12
43.5 × 58.5 mm55 parts4LNo license2STM32
Project-09
ampnics
42.5 × 58.5 mm51 parts4LNo license2STM32
STM32 gps tracker
hammadurrehman2006
46 × 60.3 mm53 parts4LNo license1STM32
STM32 GPS Tracking Module
tejashviraj19
42.5 × 58.5 mm51 parts4LNo license1STM32
GPS tracker with STM32
shubham31637
45.9 × 61.5 mm50 parts4LNo license1RP2040/RP2350
SlimDash rev1
mizma
157.1 × 131.5 mm137 parts2LCC-BY-SA-4.00GSM communications SIM800 breakout
SolderedElectronics
38 × 54 mm54 parts2LTAPR-OHL-1.00STM32
GPS TRACKER
HarshaKaushalya
42.5 × 58.5 mm53 parts4LNo license0STM32
GPS-Tracker
HarshBihani18
35 × 53 mm53 parts2LNo license0RP2040/RP2350
Low profile
ryoo14
228.8 × 76.2 mm123 parts2LNo license3RP2040/RP2350
SlimDash rev1-kicad rounded
mizma
157.1 × 131.5 mm137 parts2LCC-BY-SA-4.00STM32
Flashlight stm32-dev
ahmadtak-3212
120 × 35 mm77 parts6LNo license0STM32
STM32 GPS TRACKER
Sirucha16
42.5 × 58.5 mm51 parts4LNo license02G GSM breakout
SolderedElectronics
38 × 54 mm51 parts2LTAPR-OHL-1.00RP2040/RP2350
PCB RP2040-OnBoard
ryoo14
228.8 × 76.2 mm123 parts2LNo license3- schematic only · 85 partsSTM32
Flashlight full v1-1
ahmadtak-3212
85 parts6LNo license0
How designs wire the SMF05CT1G
Read from the KiCad layouts of 18 open source designs, one per repository: what each pin of the SMF05CT1G connects to, and the resistors, capacitors and other passives placed on it.
- The CATHODE pins have a series resistor on 16 of 18 designs, most often 10 kΩ (then 4.7 kΩ).
- The CATHODE pins have a capacitor to GND on 11 of 18 designs, most often 1 µF (then 100 nF).
- The ANODE pin is tied to GND on 11 of 18 designs (a signal on 7).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| CATHODEpin 1, 3, 4, 5, 6 | Connected to: A connector 76%, SIM808 21% |
|
| ANODEpin 2 | Connected to: GND 61% · a signal 39% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include GPS-Tracker by mohamedboubaker, YM60JIS by ymkn, Scorpion card pub by psk7 and GPS-Tracker by ibfarhat.
The SMF05CT1G in open source designs
The gallery holds 23 open source boards using the SMF05CT1G from 18 GitHub repositories; a typical one measures about 46 × 58.5 mm and carries around 55 components.
52% are two-layer designs, the rest use four layers or more, and 35% carry an open source license.
The most starred is GPS-Tracker by mohamedboubaker.
Parts used alongside the SMF05CT1G
Microcontrollers on boards using the SMF05CT1G
What boards using the SMF05CT1G are built for
SMF05CT1G: common questions
Where can I find a SMF05CT1G reference design?
Each of the 23 boards on this page is a real design using the SMF05CT1G. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the SMF05CT1G CATHODE pin?
The CATHODE pins have a series resistor on 16 of 18 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 18 open source designs using the SMF05CT1G.
How is the SMF05CT1G ANODE pin connected?
The ANODE pin is tied to GND on 11 of 18 designs (a signal on 7). Counted from the KiCad layouts of 18 open source designs using the SMF05CT1G.
What parts are used alongside the SMF05CT1G?
The SIM808, TPS5430DDA, STM32F030C8TX, 100N and 100U appear in the most repositories here.
Which microcontrollers do boards using the SMF05CT1G use?
Most are built on STM32 (14), RP2040/RP2350 (6) and ESP8266 (1).
How big is a typical board using the SMF05CT1G?
The median is 46 × 58.5 mm, and 52% are two-layer designs.
What is the most popular open source board using the SMF05CT1G?
By GitHub stars, GPS-Tracker by mohamedboubaker, with 40 stars.
Can I simulate one of these boards using the SMF05CT1G before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.