41 open source boards using the TPS22919DCKR
Real designs built with the TPS22919DCKR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Hardware design
Open-Authenticator
82 × 42 mm56 parts2LMIT42STM32
JBclone soldering station
Minu-IU3IRR
65 × 100 mm52 parts2LNo license13RP2040/RP2350
BitaxeBIRDS
bitaxeorg
65 × 120 mm129 parts6LCERN-OHL-S-2.06ESP32
PocketLab-Card
Jebroa77485.6 × 54 mm250 parts4LNo license2Doorlink
calebhabesh
59 × 91 mm88 parts2LMIT2- schematic only · 243 parts
Ai circuit design tests
devbisme
243 partsNo license2 RP2040/RP2350
Aster2350
Amronos
80 × 65 mm121 parts4LApache-2.01Fsoc txrx-1x2-panel
SharbelMarshi
104.2 × 50 mm73 parts4LNo license1Compact tablet
CopperPilot
28 × 125 mm385 parts8LCERN-OHL-S-2.00After
DD1SB
180 × 140 mm287 parts2LMIT0STM32
CANSAT-M2-2026
Engineer162
55 × 100 mm156 parts4LCERN-OHL-S-2.00RP2040/RP2350
OMiGaS
XiaotianGuan
92 × 44 mm120 parts4LNo license0Crab robot
triluongmh-byte
110 × 80 mm113 parts4LNo license0ESP32
EdgeLink S3 Cellular
CDonohoe-Designs
56 × 52 mm93 parts4LNo license0Nordic nRF
NRF9161-DEV-BOARD
anand2532
120 × 80 mm78 parts4LNo license0ESP32
Daily mirror
drewhirschi
100 × 100 mm74 parts4LNo license0Open micro sister
TomBonness
91 × 91 mm73 parts4LCustom license0AVR/Arduino
169 node
vsb-fei-440
50 × 55.9 mm65 parts4LMIT0Nordic nRF
Plan b
kaievns
16 × 42 mm61 parts4LNo license0STM32
CAN-Bus-Diagnostic-Adapter
Matthew-Garcia
90 × 55 mm47 parts2LNo license0ESP32
Bench breathe
rwrife
65 × 75 mm36 parts2LMIT0ESP32
MagMouse
sbarisic
60 × 95 mm273 parts4LCustom license2ESP32
PocketLab-Card pcba routing wip
Jebroa77485.6 × 54 mm246 parts4LNo license2RP2040/RP2350
Rp2350-connect
Amronos
85 × 70 mm118 parts6LApache-2.01Fsoc txrx panel
SharbelMarshi
104.2 × 90 mm73 parts4LNo license1Before
DD1SB
180 × 140 mm287 parts2LMIT0STM32
FH2 Flight Computer
EPFLRocketTeam
80 × 80 mm245 parts4LNo license0ESP32
PocketLab-Card routing working
Jebroa77485.6 × 54 mm243 parts4LNo license2ESP32
Main
sbarisic
80 × 125 mm207 parts4LCustom license2RP2040/RP2350
Atlas2350 connected LiPo development board
Amronos
80 × 75 mm115 parts4LApache-2.01Dfm-2oz
DD1SB
180 × 140 mm287 parts2LMIT0ESP32
Lower
sbarisic
70 × 100 mm92 parts2LCustom license2Dfm special finish
DD1SB
180 × 140 mm287 parts2LMIT0Raspberry Pi
Fsoc tx
SharbelMarshi
52.1 × 40 mm59 parts4LNo license1E2-native
DD1SB
180 × 140 mm287 parts2LMIT0Fsoc tx panel
SharbelMarshi
104.2 × 90 mm59 parts4LNo license1
How designs wire the TPS22919DCKR
Read from the KiCad layouts of 21 open source designs, one per repository: what each pin of the TPS22919DCKR connects to, and the resistors, capacitors and other passives placed on it.
- The NC_4 pin is left unconnected on 21 of 21 designs.
- The IN pin is tied to 3.3V on 17 of 21 designs (a signal on 4).
- The OUT pin has a capacitor to GND on 14 of 21 designs, most often 100 nF (then 1 µF).
- The QOD pin has a capacitor to GND on 10 of 21 designs, most often 100 nF (then 1 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| INpin 1 | Connected to: 3.3V 81% · a signal 19% | — |
| GNDpin 2 | Connected to: GND 100% | — |
| ONpin 3 | Connected to: The microcontroller 48% |
|
| NC_4pin 4 | Connected to: Not connected 100% | — |
| QODpin 5 | Connected to: Signal 52% · not connected 19% · 5V 29% |
|
| OUTpin 6 | Connected to: A connector 24% · 5V 33% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Hardware design by Open-Authenticator, JBclone soldering station by Minu-IU3IRR, BitaxeBIRDS by bitaxeorg and Doorlink by calebhabesh.
The TPS22919DCKR in open source designs
The gallery holds 41 open source boards using the TPS22919DCKR from 23 GitHub repositories; a typical one measures about 85.6 × 90.5 mm and carries around 121 components.
60% use four copper layers or more, and 49% carry an open source license.
The most starred is Hardware design by Open-Authenticator.
Parts used alongside the TPS22919DCKR
Microcontrollers on boards using the TPS22919DCKR
What boards using the TPS22919DCKR are built for
TPS22919DCKR: common questions
Where can I find a TPS22919DCKR reference design?
Each of the 41 boards on this page is a real design using the TPS22919DCKR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the TPS22919DCKR NC_4 pin connected?
The NC_4 pin is left unconnected on 21 of 21 designs. Counted from the KiCad layouts of 21 open source designs using the TPS22919DCKR.
How is the TPS22919DCKR IN pin connected?
The IN pin is tied to 3.3V on 17 of 21 designs (a signal on 4). Counted from the KiCad layouts of 21 open source designs using the TPS22919DCKR.
How is the TPS22919DCKR OUT pin connected?
The OUT pin has a capacitor to GND on 14 of 21 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 21 open source designs using the TPS22919DCKR.
What parts are used alongside the TPS22919DCKR?
The USBLC6-2SC6, BQ24074RGTR, SN74AHCT1G125DBVR, TPS63802DLAR and AP2112K-3.3TRG1 appear in the most repositories here.
Which microcontrollers do boards using the TPS22919DCKR use?
Most are built on ESP32 (10), RP2040/RP2350 (5), STM32 (4) and Nordic nRF (2).
How big is a typical board using the TPS22919DCKR?
The median is 85.6 × 90.5 mm, and 40% are two-layer designs.
What is the most popular open source board using the TPS22919DCKR?
By GitHub stars, Hardware design by Open-Authenticator, with 42 stars.
Can I simulate one of these boards using the TPS22919DCKR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.