43 open source boards using the ESP32-S3-WROOM-1U-N16R8

Real designs built with the ESP32-S3-WROOM-1U-N16R8, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

43 boardsClear filters|Most starred

How designs wire the ESP32-S3-WROOM-1U-N16R8

Read from the KiCad layouts of 37 open source designs, one per repository: what each pin of the ESP32-S3-WROOM-1U-N16R8 connects to, and the resistors, capacitors and other passives placed on it.

  • The EN pin has a pull-up to 3.3V on 35 of 37 designs, most often 10 kΩ (then 100 kΩ).
  • The EN pin has a capacitor to GND on 34 of 37 designs, most often 1 µF (then 100 nF).
  • The 3V3 pin is tied to 3.3V on 34 of 37 designs (a signal on 2).
  • The IO35 pin is left unconnected on 33 of 37 designs (a signal on 4).
GND_1pin 1Connected to: GND 97%
3V3pin 2Connected to: 3.3V 92%
ENpin 3Connected to: Signal 97%
  • Pull-up to 3.3V on 95% · 10 kΩ (30), 100 kΩ (1), 5.1 kΩ (1)
  • Capacitor to GND on 92% · 1 µF (24), 100 nF (8), 10 µF (3)
IO19pin 13Connected to: A connector 27%
  • Series resistor on 46% · 22 Ω (14), 27 Ω (1)
IO20pin 14Connected to: A connector 27%
  • Series resistor on 46% · 22 Ω (14), 27 Ω (1)
IO46pin 16Connected to: Not connected 84%
IO45pin 26Connected to: Not connected 86%
IO0pin 27Connected to: Signal 92%
  • Pull-up to 3.3V on 62% · 10 kΩ (19), 100 kΩ (1), 402 kΩ (1)
IO35pin 28Connected to: Not connected 89%
IO36pin 29Connected to: Not connected 86%
IO37pin 30Connected to: Not connected 89%
IO1pin 39Connected to: A connector 27% · not connected 30%
  • Pull-up to 3.3V on 35% · 10 kΩ (9), 4.7 kΩ (3), 5.1 kΩ (1)
GND_40pin 40Connected to: GND 97%
GND_41pin 41Connected to: GND 97%

27 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Moto gps rev a1 by mx3353672833-debug, 32bit by bread-modular, SmartKnob DevKit Base by SeedLabs-it and GLARE by RR-CREATOR.

The ESP32-S3-WROOM-1U-N16R8 in open source designs

The gallery holds 43 open source boards using the ESP32-S3-WROOM-1U-N16R8 from 38 GitHub repositories; a typical one measures about 64.5 × 74.3 mm and carries around 95 components.

69% use four copper layers or more, and 44% carry an open source license.

The most starred is Moto gps rev a1 by mx3353672833-debug.

Microcontrollers on boards using the ESP32-S3-WROOM-1U-N16R8

ESP32-S3-WROOM-1U-N16R8: common questions

Where can I find a ESP32-S3-WROOM-1U-N16R8 reference design?

Each of the 43 boards on this page is a real design using the ESP32-S3-WROOM-1U-N16R8. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What pull-up resistor is used on the ESP32-S3-WROOM-1U-N16R8 EN pin?

The EN pin has a pull-up to 3.3V on 35 of 37 designs, most often 10 kΩ (then 100 kΩ). Counted from the KiCad layouts of 37 open source designs using the ESP32-S3-WROOM-1U-N16R8.

How is the ESP32-S3-WROOM-1U-N16R8 3V3 pin connected?

The 3V3 pin is tied to 3.3V on 34 of 37 designs (a signal on 2). Counted from the KiCad layouts of 37 open source designs using the ESP32-S3-WROOM-1U-N16R8.

How is the ESP32-S3-WROOM-1U-N16R8 IO35 pin connected?

The IO35 pin is left unconnected on 33 of 37 designs (a signal on 4). Counted from the KiCad layouts of 37 open source designs using the ESP32-S3-WROOM-1U-N16R8.

What parts are used alongside the ESP32-S3-WROOM-1U-N16R8?

The AMS1117-3.3, USBLC6-2SC6, AP2112K-3.3, AP63203WU-7 and TUSB320LAIRWBR appear in the most repositories here.

Which microcontrollers do boards using the ESP32-S3-WROOM-1U-N16R8 use?

Most are built on ESP32 (43).

How big is a typical board using the ESP32-S3-WROOM-1U-N16R8?

The median is 64.5 × 74.3 mm, and 31% are two-layer designs.

What is the most popular open source board using the ESP32-S3-WROOM-1U-N16R8?

By GitHub stars, Moto gps rev a1 by mx3353672833-debug, with 320 stars.

Can I simulate one of these boards using the ESP32-S3-WROOM-1U-N16R8 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part