20 open source boards using the CC1101

Real designs built with the CC1101, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

20 boardsClear filters|Most starred

How designs wire the CC1101

Read from the KiCad layouts of 13 open source designs, one per repository: what each pin of the CC1101 connects to, and the resistors, capacitors and other passives placed on it.

  • The SO/GDO1_2 pin is tied to GND on 8 of 13 designs (a signal on 5).
  • The GDO0_6 pin is left unconnected on 8 of 13 designs (a signal on 5).
  • The XOSC_Q2_10 pin has a crystal on 5 of 9 designs, most often 26 MHz.
  • The XOSC_Q2_10 pin has a capacitor to GND on 4 of 9 designs, most often 5 pF (then 18 pF).
SO/GDO1_2pin 2Connected to: GND 62% · a signal 38%
DCOUPL_5pin 5Connected to: The microcontroller 54%, a connector 31%
  • Capacitor to GND on 31% · 100 nF (4)
GDO0_6pin 6Connected to: Not connected 62% · a signal 38%
XOSC_Q1_8pin 8Connected to: The microcontroller 54%
  • Crystal on 38% · 26 MHz (4)
  • Capacitor to GND on 31% · 5 pF (1), 18 pF (1), 12 pF (1)
AVDD1_9pin 9Connected to: 3.3V 44% · not connected 22% · a signal 33%
  • Decoupling capacitor on 33% · 10 nF (3), 220 pF (3), 100 nF (3)
XOSC_Q2_10pin 10Connected to: Signal 56% · GND 33%
  • Crystal on 56% · 26 MHz (4)
  • Capacitor to GND on 44% · 5 pF (1), 18 pF (1), 15 pF (1)
AVDD2_11pin 11Connected to: 3.3V 44% · GND 33%
  • Decoupling capacitor on 33% · 100 nF (5), 10 nF (3), 220 pF (3)
RF_P_12pin 12Connected to: Signal 100%
  • Inductor on 80% · 27 nH (2), 12 nH (2)
RF_N_13pin 13Connected to: Signal 100%
  • Inductor on 80% · 27 nH (2), 12 nH (2)
AVDD3_14pin 14Connected to: 3.3V 80% · a signal 20%
  • Decoupling capacitor on 60% · 100 nF (5), 10 nF (3), 220 pF (3)
AVDD4_15pin 15Connected to: 3.3V 80% · a signal 20%
  • Decoupling capacitor on 60% · 100 nF (5), 10 nF (3), 220 pF (3)
GND1_16pin 16Connected to: GND 80% · a signal 20%
RBIAS_17pin 17Connected to: Signal 100%
  • Resistor to GND on 80% · 56 kΩ (3), 10 kΩ (1)
DGUARD_18pin 18Connected to: 3.3V 80% · a signal 20%
GND2_19pin 19Connected to: GND 80% · a signal 20%

5 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include HB-UNI-644 by alexreinert, AskSinAnalyzer by stan23, RHS 3 by pa-pa and Wireless logger by bnahill.

The CC1101 in open source designs

The gallery holds 20 open source boards using the CC1101 from 14 GitHub repositories; a typical one measures about 69.8 × 58 mm and carries around 55 components.

74% are two-layer designs, the rest use four layers or more, and 15% carry an open source license.

The most starred is HB-UNI-644 by alexreinert.

Microcontrollers on boards using the CC1101

CC1101: common questions

Where can I find a CC1101 reference design?

Each of the 20 boards on this page is a real design using the CC1101. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the CC1101 SO/GDO1_2 pin connected?

The SO/GDO1_2 pin is tied to GND on 8 of 13 designs (a signal on 5). Counted from the KiCad layouts of 13 open source designs using the CC1101.

How is the CC1101 GDO0_6 pin connected?

The GDO0_6 pin is left unconnected on 8 of 13 designs (a signal on 5). Counted from the KiCad layouts of 13 open source designs using the CC1101.

How is the CC1101 XOSC_Q2_10 pin connected?

The XOSC_Q2_10 pin has a crystal on 5 of 9 designs, most often 26 MHz. Counted from the KiCad layouts of 13 open source designs using the CC1101.

What parts are used alongside the CC1101?

The MAX1724, ATMEGA328P-AU, AM1S-2403S, AMS1117-3.3 and AT24CS32 appear in the most repositories here.

Which microcontrollers do boards using the CC1101 use?

Most are built on AVR/Arduino (11), STM32 (4), ESP32 (3) and RP2040/RP2350 (1).

How big is a typical board using the CC1101?

The median is 69.8 × 58 mm, and 74% are two-layer designs.

What is the most popular open source board using the CC1101?

By GitHub stars, HB-UNI-644 by alexreinert, with 104 stars.

Can I simulate one of these boards using the CC1101 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part