20 open source boards using the ESP32-C6-WROOM-1
Real designs built with the ESP32-C6-WROOM-1, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Hackbat esp32
thehackbat
100 × 40 mm59 parts2LNo license12RP2040/RP2350
Mainboard
mincrmatt12
136.3 × 71.1 mm160 parts4LMIT11ESP32
Tanmatsu hardware
Nicolai-Electronics
114.9 × 129.9 mm320 parts4LCERN-OHL-P-2.09ESP32
WizServoTester
Abean2k
100 × 60.5 mm31 parts2LMIT5ESP32
SCARA-Robot-Based on-ESP32-C6
jobitjoseph
91.6 × 65 mm63 parts2LNo license4ESP32
Esp32-c6-environmental logger
pushtiujeniya
75 × 56.4 mm59 parts4LNo license4ESP32
Why2025
ranzbak
114.9 × 129.9 mm327 parts4LNo license1ESP32
Spider Upper
ucb-bar
63 × 63 mm74 parts2LNo license1ESP32
ZTank
akira215
49 × 91 mm60 parts2LGPL-3.01ESP32
Hard-EnvSens
IgorFJensen
60 × 60 mm102 parts2LNo license0ESP32
Waste-Classification using-ML
jobitjoseph
91.6 × 65 mm62 parts2LNo license0ESP32
ESP32-C6 interface
KakuheikiCreator
53.3 × 91.4 mm58 parts2LMIT0ESP32
Overture
stanciugabriel
92 × 50 mm46 parts2LNo license0ESP32
ESP32C6-DEMO-BOARD
yogith-mr
50 × 50 mm38 parts4LNo license0ESP32
LongCat
nabeellagi
49 × 119.8 mm37 parts4LNo license0ESP32
TwinBusExpander
Qeteshpony
30 × 36.5 mm24 parts4LBSD-2-Clause0ESP32
Top board pizero
ZeroPhone
111 × 80 mm249 parts2LCERN-OHL-S-2.02ESP32
ESP32C3 Upper
ucb-bar
60 × 60 mm58 parts2LNo license1ESP32
Zone syntax test
gokcesena53
90 × 55 mm89 parts4LMIT0RP2040/RP2350
Zpn devboard
CRImier
100 × 100 mm160 parts4LGPL-3.0254
How designs wire the ESP32-C6-WROOM-1
Read from the KiCad layouts of 19 open source designs, one per repository: what each pin of the ESP32-C6-WROOM-1 connects to, and the resistors, capacitors and other passives placed on it.
- The 3V3 pin is tied to 3.3V on 19 of 19 designs.
- The EN/CHIP_PU pin has a pull-up to 3.3V on 15 of 19 designs, most often 10 kΩ (then 100 kΩ).
- The EN/CHIP_PU pin has a capacitor to GND on 14 of 19 designs, most often 100 nF (then 1 µF).
- The GPIO8 pin has a pull-up to 3.3V on 12 of 17 designs, most often 10 kΩ (then 100 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1, 28, 29 | Connected to: GND 100% | — |
| 3V3pin 2 | Connected to: 3.3V 100% | — |
| EN/CHIP_PUpin 3 | Connected to: A connector 32%, the microcontroller 21% |
|
| MTCK/GPIO6/ADC1_CH6pin 6 | Connected to: A connector 24% |
|
| MTDO/GPIO7pin 7 | Connected to: A connector 33% · not connected 17% |
|
| GPIO8pin 10 | Connected to: The microcontroller 24% |
|
| GPIO12/USB_D-pin 13 | Connected to: A connector 42%, USBLC6-2SC6 26% |
|
| GPIO13/USB_D+pin 14 | Connected to: A connector 42%, USBLC6-2SC6 26% |
|
| GPIO9pin 15 | Connected to: The microcontroller 22%, a connector 22% |
|
| GPIO18pin 16 | Connected to: A connector 32% |
|
| GPIO19pin 17 | Connected to: A connector 26% · not connected 16% |
|
| GPIO20pin 18 | Connected to: A connector 21% · not connected 21% |
|
| GPIO23pin 21 | Connected to: Signal 79% · not connected 21% |
|
| NCpin 22 | Connected to: Not connected 100% | — |
13 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Zpn devboard by CRImier, Hackbat esp32 by thehackbat, Mainboard by mincrmatt12 and Tanmatsu hardware by Nicolai-Electronics.
The ESP32-C6-WROOM-1 in open source designs
The gallery holds 20 open source boards using the ESP32-C6-WROOM-1 from 19 GitHub repositories; a typical one measures about 90.8 × 64 mm and carries around 61 components.
55% are two-layer designs, the rest use four layers or more, and 45% carry an open source license.
The most starred is Zpn devboard by CRImier.
Parts used alongside the ESP32-C6-WROOM-1
Microcontrollers on boards using the ESP32-C6-WROOM-1
What boards using the ESP32-C6-WROOM-1 are built for
ESP32-C6-WROOM-1: common questions
Where can I find a ESP32-C6-WROOM-1 reference design?
Each of the 20 boards on this page is a real design using the ESP32-C6-WROOM-1. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the ESP32-C6-WROOM-1 3V3 pin connected?
The 3V3 pin is tied to 3.3V on 19 of 19 designs. Counted from the KiCad layouts of 19 open source designs using the ESP32-C6-WROOM-1.
What pull-up resistor is used on the ESP32-C6-WROOM-1 EN/CHIP_PU pin?
The EN/CHIP_PU pin has a pull-up to 3.3V on 15 of 19 designs, most often 10 kΩ (then 100 kΩ). Counted from the KiCad layouts of 19 open source designs using the ESP32-C6-WROOM-1.
What pull-up resistor is used on the ESP32-C6-WROOM-1 GPIO8 pin?
The GPIO8 pin has a pull-up to 3.3V on 12 of 17 designs, most often 10 kΩ (then 100 kΩ). Counted from the KiCad layouts of 19 open source designs using the ESP32-C6-WROOM-1.
What parts are used alongside the ESP32-C6-WROOM-1?
The USBLC6-2SC6, AMS1117-3.3, 74LVC2G02HD4-7, ADP7118AUJZ-3.3-R7 and AP2112K-3.3 appear in the most repositories here.
Which microcontrollers do boards using the ESP32-C6-WROOM-1 use?
Most are built on ESP32 (18) and RP2040/RP2350 (2).
How big is a typical board using the ESP32-C6-WROOM-1?
The median is 90.8 × 64 mm, and 55% are two-layer designs.
What is the most popular open source board using the ESP32-C6-WROOM-1?
By GitHub stars, Zpn devboard by CRImier, with 254 stars.
Can I simulate one of these boards using the ESP32-C6-WROOM-1 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.