47 open source boards using the PCF8574
Real designs built with the PCF8574, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP8266
TranspOtterNG
Jana-Marie
100 × 45 mm59 parts2LNo license51ESP32
Iotuz esp32-hardware
CCHS-Melbourne
150 × 95 mm97 parts2LTAPR-OHL-1.035ESP32
Charge Controller
jharvey
139.7 × 88.9 mm157 parts2LNo license24Ass shield
immortalserg
79.6 × 79.6 mm200 parts2LNo license12PDB
pioneers
112.1 × 88.3 mm72 parts2LNo license8RP2040/RP2350
Pico synth
HackerSchool
164 × 82.4 mm141 parts2LGPL-3.05ESP8266
DraadloosDeurbel
pappavis
51.8 × 58.4 mm25 parts2LMIT4Raspberry Pi
PortablePi v89
lucahttp
109.2 × 158.7 mm72 parts2LNo license2Pcb pox
geertu
91.9 × 68 mm64 parts2LNo license2ESP8266
Sodastream power mod
gschwaer
78 × 46.3 mm43 parts2LUnlicense2ESP32
Nixie
Synthron
240 × 70 mm311 parts4LNo license1LabnodeIO
das-labor
54.4 × 71.9 mm79 parts2LNo license1ESP8266
Rustypill
Determinant
70 × 52 mm56 parts2LNo license1AVR/Arduino
Tachometer
PotatoX
78.6 × 60.8 mm48 parts2LCC-BY-NC-4.01PRODIGY-MOTHERBOARD
mark69163
160 × 120 mm333 parts4LNo license0ESP32
Hardware
Capibator
101.5 × 64.4 mm108 parts2LNo license0ESP8266
PeterThePowerMeter
CtrlAltJon
57.5 × 79 mm76 parts2LMIT0Relay board
marvec
149.9 × 89.5 mm62 parts2LApache-2.00ESP8266
ESP8266-Cherry-MX-Board
hampussandberg
33 × 90 mm59 parts2LNo license0Mymacro
HJRaptor
100 × 100 mm55 parts2LNo license0AVR/Arduino
Micro mp
c04022004
100 × 40 mm47 parts2LNo license010000001
gitlunard
45.7 × 98 mm46 partsNo license0ESP8266
ControlUnitInput
spotlesscoder
96.1 × 90.1 mm43 parts2LCERN-OHL-1.20AVR/Arduino
UpsKeypadTerminal
kbittle
109.2 × 80 mm39 parts2LNo license0ESP8266
Light remote controller HW
easilok
86.3 × 48.5 mm34 parts2LNo license0Pcbs
TomHodson
24.3 × 92.3 mm14 parts2LMIT0PD243X-I2C-Adapter
galjonsfigur
42.5 × 20.1 mm11 parts2LApache-2.00- schematic only · 146 partsRaspberry Pi
The-Key-Crusher
Arnost55
146 partsNo license0 Arm v3
evezor
250.2 × 63.3 mm100 parts4LCERN-OHL-P-2.0126Ass shield (2-я копия)
immortalserg
80 × 80 mm193 parts2LNo license12ESP32
Esp32-lora multi gateway
enriquewph
140 × 100 mm81 parts2LMIT4AVR/Arduino
V3
iley
100 × 100 mm45 parts2LMIT4Anemometer
KhazAkar
34 × 13.5 mm9 parts2LMIT4AVR/Arduino
ArduinoController
frep
150 × 80 mm100 parts2LNo license2ESP32
Untitled
zeankundev
95.8 × 97.5 mm152 parts2LNo license1ESP32
SCAN mainboard
jjsprandel
100 × 70 mm54 parts2LCC-BY-NC-4.01
How designs wire the PCF8574
Read from the KiCad layouts of 38 open source designs, one per repository: what each pin of the PCF8574 connects to, and the resistors, capacitors and other passives placed on it.
- The SCL pin has a pull-up to 3.3V on 26 of 38 designs, most often 4.7 kΩ (then 10 kΩ).
- The SDA pin has a pull-up to 3.3V on 26 of 38 designs, most often 4.7 kΩ (then 10 kΩ).
- The INT pin is left unconnected on 24 of 38 designs (a signal on 13).
- The VDD pin has a decoupling capacitor on 16 of 38 designs, most often 100 nF (then 1 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VSSpin 8 | Connected to: GND 95% | — |
| INTpin 13 | Connected to: Not connected 63% · a signal 34% | — |
| SCLpin 14 | Connected to: The microcontroller 53%, a connector 50%, PCF8574 21% |
|
| SDApin 15 | Connected to: The microcontroller 53%, a connector 50%, PCF8574 21% |
|
| VDDpin 16 | Connected to: 3.3V 92% |
|
11 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Arm v3 by evezor, TranspOtterNG by Jana-Marie, Iotuz esp32-hardware by CCHS-Melbourne and Charge Controller by jharvey.
The PCF8574 in open source designs
The gallery holds 47 open source boards using the PCF8574 from 40 GitHub repositories; a typical one measures about 93.9 × 75.4 mm and carries around 62 components.
87% are two-layer designs, the rest use four layers or more, and 38% carry an open source license.
The most starred is Arm v3 by evezor.
Parts used alongside the PCF8574
Microcontrollers on boards using the PCF8574
What boards using the PCF8574 are built for
PCF8574: common questions
Where can I find a PCF8574 reference design?
Each of the 47 boards on this page is a real design using the PCF8574. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the PCF8574 SCL pin?
The SCL pin has a pull-up to 3.3V on 26 of 38 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 38 open source designs using the PCF8574.
What pull-up resistor is used on the PCF8574 SDA pin?
The SDA pin has a pull-up to 3.3V on 26 of 38 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 38 open source designs using the PCF8574.
How is the PCF8574 INT pin connected?
The INT pin is left unconnected on 24 of 38 designs (a signal on 13). Counted from the KiCad layouts of 38 open source designs using the PCF8574.
What parts are used alongside the PCF8574?
The AMS1117-3.3, AMS1117-5.0, ESP32-WROOM-32, ESP-12F and CH340C appear in the most repositories here.
Which microcontrollers do boards using the PCF8574 use?
Most are built on ESP32 (9), ESP8266 (8), AVR/Arduino (7) and Raspberry Pi (2).
How big is a typical board using the PCF8574?
The median is 93.9 × 75.4 mm, and 87% are two-layer designs.
What is the most popular open source board using the PCF8574?
By GitHub stars, Arm v3 by evezor, with 126 stars.
Can I simulate one of these boards using the PCF8574 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.